- 您現在的位置：買賣IC網 > PDF目錄165342 > AD5062BRJ-1500RL7 (ANALOG DEVICES INC) SERIAL INPUT LOADING, 3 us SETTLING TIME, 16-BIT DAC, PDSO8 PDF資料下載
參數資料
| 型號： | AD5062BRJ-1500RL7 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | DAC |
| 英文描述： | SERIAL INPUT LOADING, 3 us SETTLING TIME, 16-BIT DAC, PDSO8 |
| 封裝： | SOT-23, 8 PIN |
| 文件頁數： | 9/19頁 |
| 文件大?。?/td> | 639K |
| 代理商： | AD5062BRJ-1500RL7 |
Preliminary Technical Data
AD5062/AD5063
Rev. Pr C | Page 17 of 19
reference. The AD5062/AD5063 have just one reference input,
REFIN. The voltage on the reference input is used to supply the
positive input to the Dac . Therefore any error in the reference
will be reflected in the Dac.
There are 4 possible sources of error when choosing a voltage
reference for high accuracy applications; initial accuracy, ppm
drift, long term drift and output voltage noise. Initial accuracy
on the output voltage of the Dac will lead to a full scale error in
the Dac. To minimize these errors, a reference with high initial
accuracy is preferred. Also, choosing a reference with an output
trim adjustment, such as the ADR423 allow a system designer
to trim system errors out by setting a reference voltage to a
voltage other than the nominal. The trim adjustment can also
be used at temperature to trim out any error.
AD5062/3
THREE-WIRE
SERIAL
INTERFACE
SYNC
SCLK
DIN
5V
3.01v
VOUT =0VTO 3.01V
ADR423
Figure 29. ADR423 as Reference to AD5062/AD5063
Long term drift is a measure of how much the reference drifts
over time. A reference with a tight long term drift specification
ensures that the overall solution remains relatively stable
during its entire lifetime.
The temperature co-efficient of a references output voltage
affect INL,DNL TUE. A reference with a tight temperature co-
efficient specification should be chosen to reduce temperatue
dependence of the Dac output voltage on ambient conditions.
In high accuracy applications, which have a relatively low
noise budget, reference output voltage noise needs to be
considered. Choosing a reference with as low an output noise
voltage as practical for the system noise resolution required is
important. Precision voltage references such as the ADR435
produce low output noise in the 0.1-10Hz region. Examples of
some recommended precision references for use as supply to
the AD5060 are shown in the figure below..
Part list of precision references for use with
AD5062/AD5063.
Part No.
Initial
Accuracy
(mV max)
Temp Drift
(ppm
oC max)
0.1-10Hz Noise
(uV p-p typ)
ADR435
+/-6
3
3.4
ADR425
+/-6
3
3.4
ADR02
+/-5
3
15
ADR395
+/-6
25
5
Bipolar Operation Using the AD5062/AD5063
The AD5062/AD5063 has been designed for single-supply
operation but a bipolar output range is also possible using the
circuit in Figure 30. The circuit below will give an output
voltage range of ±4.096 V. Rail-to-rail operation at the
amplifier output is achievable using an AD820 or an OP295 as
the output amplifier.
The output voltage for any input code can be calculated as
follows:
V O = V DD ×
D
65536
×
R1 + R2
R1
V DD ×
R2
R1
where D represents the input code in decimal (0–16384).
With VREF = 5 V, R1 = R2 = 10 kW:
V O =
10 × D
65536
5V
This is an output voltage range of ±5 V with 0000Hex
corresponding to a –5 V output and 3FFF Hex
corresponding to a +5 V output.
AD5063
DacGND
V
DD
REF
OUT
SCLK
DIN
SYNC
+5V
+4.096V
EXTERNAL
OP AMP
BIPOLAR
OUTPUT
10u F
SERIAL
INTERFACE
0.1u F
INV
R
INV
+5V
–5V
RFB
RFB
AGND
Figure 30. Bipolar Operation with the AD5063
Using AD5062/AD5063 with an Opto-Isolated
Interface Chip.
In process-control applications in industrial environments it is
often necessary to use an opto-isolated interface to protect and
isolate the controlling circuitry from any hazardous common-
mode voltages that may occur in the area where the DAC is
functioning. Because the AD5062/AD5063 uses a three-wire
serial logic interface, the ADuM130Xifamily s an ideal way to
provide digital isolation for the DAC interface.
The ADuM130x isolators provide three independent isolation
channels in a variety of channel configurations and data rates.
相關PDF資料 |
PDF描述 |
|---|---|
| AD5204TD | 1-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL/PARALLEL ACCESS, CDIP24 |
| AD5757ACPZ-REEL7 | SERIAL INPUT LOADING, 15 us SETTLING TIME, 16-BIT DAC, QCC64 |
| AD5757ACPZ | SERIAL INPUT LOADING, 15 us SETTLING TIME, 16-BIT DAC, QCC64 |
| AD590-02 | ANALOG TEMP SENSOR-CURRENT, 298.2uA, RECTANGULAR, THROUGH HOLE MOUNT |
| AD632TH/883 | ANALOG MULTIPLIER OR DIVIDER, MBCY10 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD5062BRJ-2 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Full Accurate 16 Bit Vout nanoDac, 2.7V- 5.5V, in a Sot 23 |
| AD5062BRJ-3 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Full Accurate 16 Bit Vout nanoDac, 2.7V- 5.5V, in a Sot 23 |
| AD5062BRJZ-1 | 制造商:Analog Devices 功能描述:DAC 1CH R-2R 16BIT 8PIN SOT-23 - Bulk |
| AD5062BRJZ-1500RL7 | 功能描述:IC DAC 16BIT 2.7-5.5V SOT23-8 RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:nanoDAC™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 設置時間:4µs 位數:12 數據接口:串行 轉換器數目:2 電壓電源:單電源 功率耗散（最大）:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-uMAX 包裝:管件 輸出數目和類型:2 電壓，單極 采樣率（每秒）:* 產品目錄頁面:1398 (CN2011-ZH PDF) |
| AD5062BRJZ-1REEL7 | 功能描述:IC DAC 16BIT 2.7-5.5V SOT23-8 RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:nanoDAC™ 標準包裝:47 系列:- 設置時間:2µs 位數:14 數據接口:并聯 轉換器數目:1 電壓電源:單電源 功率耗散（最大）:55µW 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:28-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:28-SSOP 包裝:管件 輸出數目和類型:1 電流，單極；1 電流，雙極 采樣率（每秒）:* |
發布緊急采購，3分鐘左右您將得到回復。