- 您現在的位置：買賣IC網 > PDF目錄1978 > AD1871YRSZ-REEL (Analog Devices Inc)IC ADC STEREO 24BIT 96KHZ 28SSOP PDF資料下載
參數資料
| 型號： | AD1871YRSZ-REEL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 17/28頁 |
| 文件大小： | 0K |
| 描述： | IC ADC STEREO 24BIT 96KHZ 28SSOP |
| 標準包裝： | 1,500 |
| 位數： | 24 |
| 采樣率（每秒）： | 96k |
| 數據接口： | 串行，SPI? |
| 轉換器數目： | 2 |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 105°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-SSOP（0.209"，5.30mm 寬） |
| 供應商設備封裝： | 28-SSOP |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 4 個單端，單極 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
AD1871
–24–
REV. 0
Peak Reading Registers
The Peak Reading Registers are read-only registers that can be
enabled to track-and-hold the peak ADC reading from each
channel. The peak reading feature is enabled by setting Bit PRE
in Control Register I. The peak reading value is contained in the
six LSBs of the 10-bit readback word. The result is binary coded
where each LSB is equivalent to –1 dBFS with all zeros cor-
responding to full scale (0 dBFS) and all ones corresponding
to –63 dBFS (see Table XVI). When Bit PRE is set, the peak
reading per channel is stored in the appropriate peak register.
Once the register is read, the register value is set to zero and is
updated by subsequent conversions.
Table XVI. Peak Reading Result Format
Code
AxP
5
4
3
2
1
0
Level
00
0
0 dBFS
00
0
1
–1 dBFS
00
1
0
–2 dBFS
11
1
110
–62 dBFS
11
1
111
–63 dBFS
A Peak Reading Register read cycle is detailed in Figure 21.
EXTERNAL CONTROL
The AD1871 can be configured for external hardware control of
a subset of the device functionality. This functionality includes
Master/Slave Mode select, MCLK select, and serial data
format select. External control is enabled by tying the XCTRL
Pin high as shown in Figure 22.
256
/512
M
/S
DF0
DF1
AD1871
XCTRL
VDD
Figure 22. External Control Configuration
Table XIV. Peak Reading Register I (Address 0011b, Read-Only)
15–12
11
10
9
87
6
5
432
10
0011
1
0
A0P5
A0P4
A0P3
A0P2
A0P1
A0P0
9–6
Reserved
(Always Set to Zero)
5–0
A0P5–A0P0
Left Channel Peak Reading (Valid Only When PRE = 1)
Table XV. Peak Reading Register II (Address 0100b, Read-Only)
15–12
11
10
9
87
6
5
432
10
0100
1
0
A1P5
A1P4
A1P3
A1P2
A1P1
A1P0
9–6
Reserved
(Always Set to Zero)
5–0
A1P5–A1P0
Right Channel Peak Reading (Valid Only When PRE = 1)
Master/Slave Select
The
Master/Slave hardware select (Pin 5, CLATCH/[M/S])
is equivalent to setting the
M/S Bit of Control Register II. If set
low, the device is placed in Master Mode, whereby the LRCLK
and BCLK signals are outputs from the AD1871.
When
M/S is set high, the device is in Slave Mode, whereby the
LRCK and BCLK signals are inputs to the AD1871.
MCLK Mode Select
The MCLK Mode hardware select (Pin 2, CCLK/[
256/512]) is
a subset of the MCLK Mode selection that is determined by
Bits CM1–CM0 of Control Register X. When the hardware pin
is low, the device operates with an MCLK that is 256
fS; if the
pin is set high, the device operates with an MCLK that is 512
fS.
Serial Data Format Select
The Serial Data Format hardware select (Pins 3 and 4, DF0/
COUT and DF1/CIN) is equivalent to setting Bits DF1–DF0 of
Control Register II. See Table VIII.
In External Control Mode, all functions other than those
selected by the hardware select pins (
Master/Slave Mode select,
MCLK select, and Serial Data Format select) are in their
default (power-on) state.
MODULATOR MODE
When the device is in Modulator Mode (MME Bit is set to 1),
the D[0–3] pins are enabled as data outputs, while the COUT
pin becomes MODCLK, a high speed sampling clock (nomi-
nally at 128
fS). The MODCLK enables successive data from
the left and right channel modulators with left channel modula-
tor data being valid in the low phase of MODCLK, while right
channel modulator data is valid under the high phase of MODCLK
(see Modulator Mode Timing in Figure 6).
The Modulator Mode is designed to be used for applications
such as direct stream digital (DSD) where modulator data is
stored directly to the recording media without decimation and
filtering to a lower sample rate. DSD is specified at a rate of
64
fS, whereas the AD1871 outputs at 128
fS,
requiring an intermediate remodulator that downsamples to
64
fS and generates a single-bit output steam.
相關PDF資料 |
PDF描述 |
|---|---|
| AD1877JRZ-RL | IC ADC STEREO 16BIT 28-SOIC |
| AD1974YSTZ-RL | IC CODEC 4CH ADC W/PLL 48-LQFP |
| AD2S99BP | IC OSC SINUSOIDAL 20KHZ 20-PLCC |
| AD5310BRM | IC DAC 10BIT R-R W/BUFF 8-MSOP |
| AD5341BRUZ | IC DAC 12BIT SNGL VOUT 20TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD1876 | 制造商:AD 制造商全稱:Analog Devices 功能描述:16-Bit 100 kSPS Sampling ADC |
| AD1876JN | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| AD1877 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Single-Supply 16-Bit Stereo ADC |
| AD1877JR | 制造商:Rochester Electronics LLC 功能描述:IC, +5V 16-BIT STEREO ADC - Bulk 制造商:Analog Devices 功能描述:IC +5V 16-BIT STEREO ADC |
| AD1877JR-REEL | 制造商:Rochester Electronics LLC 功能描述:SINGLE SUPPLY 5V 16-BIT STERO ADC - Tape and Reel 制造商:Analog Devices 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。