- 您現在的位置：買賣IC網 > Datasheet目錄59 > A3251LUA-T (Allegro Microsystems Inc)IC SW HALL EFFECT UNI 3-SIP Datasheet資料下載
參數資料
| 型號： | A3251LUA-T |
| 廠商： | Allegro Microsystems Inc |
| 文件頁數： | 10/16頁 |
| 文件大?。?/td> | 300K |
| 描述： | IC SW HALL EFFECT UNI 3-SIP |
| 標準包裝： | 500 |
| 傳感范圍： | 50G |
| 類型： | 單極開關 |
| 電源電壓： | 4.2 V ~ 24 V |
| 電流 - 電源： | 10mA |
| 電流 - 輸出（最大）： | 20mA |
| 輸出類型： | 數字，開路集電極 |
| 特點： | 穩壓電壓 |
| 工作溫度： | -40°C ~ 150°C |
| 封裝/外殼： | 3-SIP |
| 供應商設備封裝： | 3-SIP |
| 包裝： | 散裝 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁
Field-Programmable, Chopper-Stabilized,
Unipolar Hall-Effect Switches
A3250 and
A3251
9
Allegro MicroSystems, Inc.
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
V
PH
V+
t
V
PM
V
PL
0
T
d(1)
T
d(0)
T
d(P)
Figure 1. Pulse amplitudes and durations
PROGRAMMING PROTOCOL CHARACTERISTICS, T
A
= 25篊, unless otherwise noted
Characteristic
Symbol
Test Conditions
Min. Typ. Max. Units
Programming Voltage
1
V
PL
Minimum voltage range during programming
4.5 5.0 5.5 V
V
PM
10 11 12
V
V
PH
23 25 26
V
Programming Current
2
I
PP
Maximum supply current during programming
500 mA
Pulse Width
t
d(0)
OFF time between programming bits
20
約
t
d(1)
Pulse duration (ON time) for enable, address, fuse
blowing or lock bits
20
約
t
d(P)
Pulse duration (ON time) for fuse blowing
100 300
約
Pulse Rise Time
t
r
V
PL
to V
PM
;
V
PL
to V
PH
11
約
Pulse Fall Time
t
f
V
PM
to V
PL
; V
PH
to V
PL
5
約
1
Programming voltages are measured at the VCC pin.
2
A bypass capacitor with a minimum capacitance of 0.1 糉 must be connected from VCC to the GND pin of the device in order to provide
the current necessary to blow the fuse.
Additional information on device programming and program-
ming products is available on www. allegromicro.com. Program-
ming hardware is available for purchase, and programming
software is available free of charge.
Programming Protocol
The operate switchpoint, B
OP
, can be field-programmed. To do
so, a coded series of voltage pulses through the VCC pin is used
to set bitfields in onboard registers. The effect on the device
output can be monitored, and the registers can be cleared and
set repeatedly until the required B
OP
is achieved. To make the
setting permanent, bitfield-level solid state fuses are blown, and
finally, a device-level fuse is blown, blocking any further cod-
ing. It is not necessary to program the release switchpoint, B
RP
,
because the difference between B
OP
and B
RP
, referred to as the
hysteresis, B
HYS
, is fixed.
The range of values between B
OP(min)
and B
OP(max)
is scaled to
64 increments. The actual change in magnetic flux (G) repre-
sented by each increment is indicated by B
RES
(see the Operating
Characteristics table; however, testing is the only method for
verifying the resulting B
OP
). For programming, the 64 incre-
ments are individually identified using 6 data bits, which are
physically represented by 6 bitfields in the onboard registers.
By setting these bitfields, the corresponding calibration value is
programmed into the device.
Three voltage levels are used in programming the device: a low
voltage, V
PL
, a minimum required to sustain register settings; a
mid-level voltage, V
PM
, used to increment the address counter
in the device; and a high voltage, V
PH
, used to separate sets of
V
PM
pulses (when short in duration) and to blow fuses (when
long in duration). A fourth voltage level, essentially 0 V, is used
to clear the registers between pulse sequences. The pulse values
are shown in the Programming Protocol Characteristics table and
in figure 1.
Code Programming. Each bitfield must be individually set. To
do so, a pulse sequence must be transmitted for each bitfield that
is being set to 1. If more than one bitfield is being set to 1, all
pulse sequences must be sent, one after the other, without allow-
ing V
CC
to fall to zero (which clears the registers).
The same pulse sequence is used to provisionally set bitfields as
is used to permanently set bitfield-level fuses. The only differ-
ence is that when provisionally setting bitfields, no fuse-blowing
pulse is sent at the end of the pulse sequence.
相關PDF資料 |
PDF描述 |
|---|---|
| A3260LUA | IC SW HALL EFFECT BIPO 3-SIP |
| A3282LLHLT-T | IC SW HALL EFFECT CHOPPER SOT23W |
| A3340EUA-T | IC SW HALL EFFECT PREC 3-SIP |
| A3422LKA-T | IC SENSOR DIRECT/DETECT 5-SIP |
| AAH002-02 | SENSORS MAGNETIC FIELD 8SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A3251LUATL | 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:Field-Programmable, Chopper-Stabilized Unipolar Hall-Effect Switches |
| A325400284-200 | 制造商: 功能描述: 制造商:undefined 功能描述: |
| A32550-0009 | 功能描述:重負荷電源連接器 A32 SOCKET 50mm 50MMSKTCON RoHS:否 制造商:Hirose Connector 系列:PS2 產品類型:Connectors 位置/觸點數量: 端接類型:Crimp 觸點材料: 觸點電鍍:Gold 電壓額定值: 電流額定值:300 A 附件類型: |
| A32550-0049 | 功能描述:重負荷電源連接器 A32 SOCKET 50mm WITH 2 AUX/2 PILOT CONT RoHS:否 制造商:Hirose Connector 系列:PS2 產品類型:Connectors 位置/觸點數量: 端接類型:Crimp 觸點材料: 觸點電鍍:Gold 電壓額定值: 電流額定值:300 A 附件類型: |
| A32550-1009 | 功能描述:重負荷電源連接器 A32 SOCKET 50mm 50MMSKTCON RoHS:否 制造商:Hirose Connector 系列:PS2 產品類型:Connectors 位置/觸點數量: 端接類型:Crimp 觸點材料: 觸點電鍍:Gold 電壓額定值: 電流額定值:300 A 附件類型: |
發布緊急采購，3分鐘左右您將得到回復。