- 您現在的位置：買賣IC網 > PDF目錄24857 > 94201DF (INTEGRATED DEVICE TECHNOLOGY INC) 200 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO56 PDF資料下載
參數資料
| 型號： | 94201DF |
| 廠商： | INTEGRATED DEVICE TECHNOLOGY INC |
| 元件分類： | 時鐘產生/分配 |
| 英文描述： | 200 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO56 |
| 封裝： | 0.300 INCH, ROHS COMPLIANT, SSOP-56 |
| 文件頁數： | 7/21頁 |
| 文件大?。?/td> | 222K |
| 代理商： | 94201DF |
15
ICS94201
0428B - 11/28/05
Fig. 1
Shared Pin Operation -
Input/Output Pins
The I/O pins designated by (input/output) on the ICS94201
serve as dual signal functions to the device. During initial
power-up, they act as input pins. The logic level (voltage) that
is present on these pins at this time is read and stored into a 5-
bit internal data latch. At the end of Power-On reset, (see AC
characteristics for timing values), the device changes the
mode of operations for these pins to an output function. In this
mode the pins produce the specified buffered clocks to external
loads.
To program (load) the internal configuration register for these
pins, a resistor is connected to either the VDD (logic 1) power
supply or the GND (logic 0) voltage potential. A 10 Kilohm
(10K) resistor is used to provide both the solid CMOS
programming voltage needed during the power-up
programming period and to provide an insignificant load on
the output clock during the subsequent operating period.
Via to
VDD
Clock trace to load
Series Term. Res.
Programming
Header
Via to Gnd
Device
Pad
2K
W
8.2K
W
Figure 1 shows a means of implementing this function when
a switch or 2 pin header is used. With no jumper is installed
the pin will be pulled high. With the jumper in place the pin
will be pulled low. If programmability is not necessary, than
only a single resistor is necessary. The programming resistors
should be located close to the series termination resistor to
minimize the current loop area. It is more important to locate
the series termination resistor close to the driver than the
programming resistor.
相關PDF資料 |
PDF描述 |
|---|---|
| 94201DFT | 200 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO56 |
| 08052C103MA74A | General Specifications |
| 94211AFLFT | 150 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO48 |
| 94211AFT | 150 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO48 |
| 94211AFLF | 150 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO48 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 94201DF-995LF | 制造商:Integrated Device Technology Inc 功能描述:IDT 94201DF-995LF GENERAL PURPOSE SEMICONDUCTORS - Rail/Tube 制造商:Integrated Device Technology Inc 功能描述:IDT 94201DF-995LF General Purpose Semiconductors |
| 94201DFLF | 功能描述:時鐘發生器及支持產品 RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56 |
| 94201DFLFT | 功能描述:時鐘發生器及支持產品 RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56 |
| 94202 | 功能描述:ION BAR ASSEMBLY 制造商:desco 系列:- 零件狀態:有效 類型:電離器 安裝類型:- 電壓 - 輸入:- 標準包裝:1 |
| 9420-2"X36YD | 功能描述:2 X 36 YD BULK 制造商:3m 系列:* 零件狀態:有效 標準包裝:24 |
發布緊急采購，3分鐘左右您將得到回復。