- 您現在的位置：買賣IC網 > PDF目錄24832 > 935270019512 (NXP SEMICONDUCTORS) 2 CHANNEL(S), 5M bps, SERIAL COMM CONTROLLER, PQCC44 PDF資料下載
參數資料
| 型號： | 935270019512 |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 2 CHANNEL(S), 5M bps, SERIAL COMM CONTROLLER, PQCC44 |
| 封裝： | PLASTIC, MS-018, SOT-187-2, LCC-44 |
| 文件頁數： | 6/51頁 |
| 文件大小： | 667K |
| 代理商： | 935270019512 |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁
Philips Semiconductors
SC16C2550
Dual UART with 16 bytes of transmit and receive FIFOs
and infrared (IrDA) encoder/decoder
Product data
Rev. 02 — 14 March 2003
14 of 47
9397 750 11204
Koninklijke Philips Electronics N.V. 2003. All rights reserved.
6.9 DMA operation
The SC16C2550 FIFO trigger level provides additional exibility to the user for block
mode operation. LSR[5,6] provide an indication when the transmitter is empty or has
an empty location(s). The user can optionally operate the transmit and receive FIFOs
in the DMA mode (FCR[3]). When the transmit and receive FIFOs are enabled and
the DMA mode is de-activated (DMA Mode 0), the SC16C2550 activates the interrupt
output pin for each data transmit or receive operation. When DMA mode is activated
(DMA Mode 1), the user takes the advantage of block mode operation by loading or
unloading the FIFO in a block sequence determined by the receive trigger level and
the transmit FIFO. In this mode, the SC16C2550 sets the TXRDY (or RXRDY) output
pin when characters in the transmit FIFO is below 16, or the characters in the receive
FIFOs are above the receive trigger level.
6.10 Loop-back mode
The internal loop-back capability allows on-board diagnostics. In the loop-back mode,
the normal modem interface pins are disconnected and recongured for loop-back
internally (see Figure 6). MCR[0-3] register bits are used for controlling loop-back
diagnostic testing. In the loop-back mode, the transmitter output (TX) and the receiver
input (RX) are disconnected from their associated interface pins, and instead are
connected together internally. The CTS, DSR, CD, and RI are disconnected from
their normal modem control inputs pins, and instead are connected internally to RTS,
DTR, MCR[3] (OP2) and MCR[2] (OP1). Loop-back test data is entered into the
transmit holding register via the user data bus interface, D0-D7. The transmit UART
serializes the data and passes the serial data to the receive UART via the internal
loop-back connection. The receive UART converts the serial data back into parallel
Table 6:
Baud rate generator programming table using a 1.8432 MHz clock
Output
baud rate
Output
16
× clock divisor
(decimal)
Output
16
× clock divisor
(HEX)
DLM
program value
(HEX)
DLL
program value
(HEX)
50
2304
900
09
00
75
1536
600
06
00
110
1047
417
04
17
150
768
300
03
00
300
384
180
01
80
600
192
C0
00
C0
1200
96
60
00
60
2400
48
30
00
30
3600
32
20
00
20
4800
24
18
00
18
7200
16
10
00
10
9600
12
0C
00
0C
19.2 k
6
06
00
06
38.4 k
3
03
00
03
57.6 k
2
02
00
02
115.2 k
1
01
00
01
相關PDF資料 |
PDF描述 |
|---|---|
| 935270019518 | 2 CHANNEL(S), 5M bps, SERIAL COMM CONTROLLER, PQCC44 |
| 935270020128 | 2 CHANNEL(S), 5M bps, SERIAL COMM CONTROLLER, PQFP48 |
| 935270050157 | 4 CHANNEL(S), 5M bps, SERIAL COMM CONTROLLER, PQFP64 |
| 935270052157 | 4 CHANNEL(S), 5M bps, SERIAL COMM CONTROLLER, PQFP64 |
| 935270052151 | 4 CHANNEL(S), 5M bps, SERIAL COMM CONTROLLER, PQFP64 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 935270713557 | 制造商:NXP Semiconductors 功能描述:SUB ONLY IC CHP |
| 935270792551 | 制造商:NXP Semiconductors 功能描述:IC BUFF DVR TRI-ST 16BIT 56VFBGA |
| 935270792557 | 制造商:NXP Semiconductors 功能描述:IC BUFF DVR TRI-ST 16BIT 56VFBGA |
| 935270793551 | 制造商:NXP Semiconductors 功能描述:IC BUS TRCVR 3-ST 16BIT 56VFBGA |
| 935270793557 | 制造商:NXP Semiconductors 功能描述:IC BUS TRCVR 3-ST 16BIT 56VFBGA |
發布緊急采購，3分鐘左右您將得到回復。