參數資料
型號： 935270019512
廠商： NXP SEMICONDUCTORS
元件分類： 微控制器/微處理器
英文描述： 2 CHANNEL(S), 5M bps, SERIAL COMM CONTROLLER, PQCC44
封裝： PLASTIC, MS-018, SOT-187-2, LCC-44
文件頁數： 11/51頁
文件大?。?/td> 667K
代理商： 935270019512
Philips Semiconductors
SC16C2550
Dual UART with 16 bytes of transmit and receive FIFOs
and infrared (IrDA) encoder/decoder
Product data
Rev. 02 — 14 March 2003
19 of 47
9397 750 11204
Koninklijke Philips Electronics N.V. 2003. All rights reserved.
7.2.2
IER versus Receive/Transmit FIFO polled mode operation
When FCR[0] = logic 1, resetting IER[0-3] enables the SC16C2550 in the FIFO
polled mode of operation. In this mode, interrupts are not generated and the user
must poll the LSR register for TX and/or RX data status. Since the receiver and
transmitter have separate bits in the LSR either or both can be used in the polled
mode by selecting respective transmit or receive control bit(s).
LSR[0] will be a logic 1 as long as there is one byte in the receive FIFO.
LSR[1-4] will provide the type of receive errors, or a receive break, if encountered.
LSR[5] will indicate when the transmit FIFO is empty.
LSR[6] will indicate when both the transmit FIFO and transmit shift register are
empty.
LSR[7] will show if any FIFO data errors occurred.
7.3 FIFO Control Register (FCR)
This register is used to enable the FIFOs, clear the FIFOs, set the receive FIFO
trigger levels, and select the DMA mode.
7.3.1
DMA mode
Mode 0 (FCR bit 3 = 0): Set and enable the interrupt for each single transmit or
receive operation, and is similar to the 16C450 mode. Transmit Ready (TXRDY) on
PLCC44 and LQFP48 packages will go to a logic 0 whenever the FIFO (THR, if FIFO
is not enabled) is empty. Receive Ready (RXRDY) on PLCC44 and LQFP48
packages will go to a logic 0 whenever the Receive Holding Register (RHR) is loaded
with a character.
Mode 1 (FCR bit 3 = 1): Set and enable the interrupt in a block mode operation. The
transmit interrupt is set when the transmit FIFO is empty. TXRDY on PLCC and
LQFP48 packages remains a logic 0 as long as one empty FIFO location is available.
The receive interrupt is set when the receive FIFO lls to the programmed trigger
level. However, the FIFO continues to ll regardless of the programmed level until the
FIFO is full. RXRDY on PLCC44 and LQFP48 packages transitions LOW when the
FIFO reaches the trigger level, and transitions HIGH when the FIFO empties.
相關PDF資料
PDF描述
935270019518 2 CHANNEL(S), 5M bps, SERIAL COMM CONTROLLER, PQCC44
935270020128 2 CHANNEL(S), 5M bps, SERIAL COMM CONTROLLER, PQFP48
935270050157 4 CHANNEL(S), 5M bps, SERIAL COMM CONTROLLER, PQFP64
935270052157 4 CHANNEL(S), 5M bps, SERIAL COMM CONTROLLER, PQFP64
935270052151 4 CHANNEL(S), 5M bps, SERIAL COMM CONTROLLER, PQFP64
相關代理商/技術參數
參數描述
935270713557 制造商:NXP Semiconductors 功能描述:SUB ONLY IC CHP
935270792551 制造商:NXP Semiconductors 功能描述:IC BUFF DVR TRI-ST 16BIT 56VFBGA
935270792557 制造商:NXP Semiconductors 功能描述:IC BUFF DVR TRI-ST 16BIT 56VFBGA
935270793551 制造商:NXP Semiconductors 功能描述:IC BUS TRCVR 3-ST 16BIT 56VFBGA
935270793557 制造商:NXP Semiconductors 功能描述:IC BUS TRCVR 3-ST 16BIT 56VFBGA
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*