- 您現在的位置：買賣IC網 > PDF目錄122717 > 935262403118 (NXP SEMICONDUCTORS) 0 TIMER(S), REAL TIME CLOCK, PDSO8 PDF資料下載
參數資料
| 型號： | 935262403118 |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 時鐘/數據恢復及定時提取 |
| 英文描述： | 0 TIMER(S), REAL TIME CLOCK, PDSO8 |
| 封裝： | 3 MM, PLASTIC, TSSOP-8 |
| 文件頁數： | 19/32頁 |
| 文件大小： | 711K |
| 代理商： | 935262403118 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
Philips Semiconductors
PCF8563
Real-time clock/calendar
Product specication
16 April 1999
26 of 30
9397 750 04855
Philips Electronics N.V. 1999. All rights reserved.
During placement and before soldering, the package must be xed with a droplet of
adhesive. The adhesive can be applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the adhesive is cured.
Typical dwell time is 4 seconds at 250
°C. A mildly-activated ux will eliminate the
need for removal of corrosive residues in most applications.
14.2.3
Manual soldering
Fix the component by rst soldering two diagonally-opposite end leads. Use a low
voltage (24 V or less) soldering iron applied to the at part of the lead. Contact time
must be limited to 10 seconds at up to 300
°C.
When using a dedicated tool, all other leads can be soldered in one operation within
2 to 5 seconds between 270 and 320
°C.
14.3 Through-hole mount packages
14.3.1
Soldering by dipping or by solder wave
The maximum permissible temperature of the solder is 260
°C; solder at this
temperature must not be in contact with the joints for more than 5 seconds. The total
contact time of successive solder waves must not exceed 5 seconds.
The device may be mounted up to the seating plane, but the temperature of the
plastic body must not exceed the specied maximum storage temperature (Tstg(max)).
If the printed-circuit board has been pre-heated, forced cooling may be necessary
immediately after soldering to keep the temperature within the permissible limit.
14.3.2
Manual soldering
Apply the soldering iron (24 V or less) to the lead(s) of the package, either below the
seating plane or not more than 2 mm above it. If the temperature of the soldering iron
bit is less than 300
°C it may remain in contact for up to 10 seconds. If the bit
temperature is between 300 and 400
°C, contact may be up to 5 seconds.
相關PDF資料 |
PDF描述 |
|---|---|
| 935261475512 | 8 CHANNEL(S), 500K bps, SERIAL COMM CONTROLLER, PQCC84 |
| 9LPRS365BKLF | SPECIALTY MICROPROCESSOR CIRCUIT, PQCC64 |
| 91W-G28AC-6-CG9 | SINGLE COLOR DISPLAY CLUSTER, GREEN, 7.1 mm |
| 91W-G5AC-6-CW0 | SINGLE COLOR DISPLAY CLUSTER, GREEN, 7.1 mm |
| 94W-EAY2-S0 | SINGLE COLOR LED, AMBER, 8.5 mm |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 935264217557 | 制造商:NXP Semiconductors 功能描述:SUB ONLY IC |
| 935267356112 | 制造商:NXP Semiconductors 功能描述:IC TEA1507PN |
| 935268081112 | 制造商:NXP Semiconductors 功能描述:SUB ONLY IC |
| 935268721125 | 制造商:NXP Semiconductors 功能描述:Buffer/Line Driver 1-CH Non-Inverting 3-ST CMOS 5-Pin TSSOP T/R |
| 935269304128 | 制造商:ST-Ericsson 功能描述:IC AUDIO CODEC W/TCH SCRN 48LQFP |
發布緊急采購，3分鐘左右您將得到回復。