- 您現在的位置：買賣IC網 > PDF目錄360557 > 908E425 (飛思卡爾半導體(中國)有限公司) Integrated Quad Half H-Bridge with Power Supply, Embedded MCU, and LIN Serial Communication PDF資料下載
參數資料
| 型號： | 908E425 |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 英文描述： | Integrated Quad Half H-Bridge with Power Supply, Embedded MCU, and LIN Serial Communication |
| 中文描述： | 綜合四半僅符合電源橋，嵌入式微控制器和LIN串行通信 |
| 文件頁數： | 17/49頁 |
| 文件大?。?/td> | 490K |
| 代理商： | 908E425 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁
Analog Integrated Circuit Device Data
Freescale Semiconductor
17
908E425
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
INTERRUPTS
The 908E425 has seven different interrupt sources as
described in the following paragraphs. The interrupts can be
disabled or enabled via the SPI. After reset all interrupts are
automatically disabled.
LOW-VOLTAGE INTERRUPT
The Low-Voltage Interrupt (LVI) is related to the external
supply voltage, V
SUP
. If this voltage falls below the LVI
threshold, it will set the LVI flag. If the low-voltage interrupt is
enabled, an interrupt will be initiated.
With LVI the H-Bridges (high-side MOSFET only) and the
high-side driver are switched off. All other modules are not
influenced by this interrupt.
During STOP mode the LVI circuitry is disabled.
HIGH-VOLTAGE INTERRUPT
The High-Voltage Interrupt (HVI) is related to the external
supply voltage, V
SUP
. If this voltage rises above the HVI
threshold, it will set the HVI flag. If the High-Voltage Interrupt
is enabled, an interrupt will be initiated.
With HVI the H-Bridges (high-side MOSFET only) and the
high-side driver are switched off. All other modules are not
influenced by this interrupt.
During STOP mode the HVI circuitry is disabled.
HIGH-TEMPERATURE INTERRUPT
The High-Temperature Interrupt (HTI) is generated by the
on-chip temperature sensors. If the chip temperature is
above the HTI threshold, the HTI flag will be set. If the High-
Temperature Interrupt is enabled, an interrupt will be
initiated.
During STOP mode the HTI circuitry is disabled.
AUTONOMOUS WATCHDOG INTERRUPT (AWD )
Refer to Autonomous Watchdog
Autonomous Watchdog
(AWD) on page 37
.
LIN INTERRUPT
If the LINIE bit is set, a falling edge on the LIN pin will
generate an interrupt. During STOP mode this interrupt will
initiate a system wake-up.
HALL-EFFECT SENSOR INPUT PIN INTERRUPT
If the PHIE bit is set, the enabled Hall-Effect Sensor input
pins H1: H3 can generate an interrupt if a current above the
threshold is detected. During STOP mode this interrupt,
combined with the cyclic wake-up feature of the AWD, can
wake up the system. Refer to pin
HALL-EFFECT
SENSOR INPUT PINS (H1: H3)
.
OVERCURRENT INTERRUPT
If an overcurrent condition on a half-bridge occurs, the
high-side or the HVDD output is detected and the OCIE bit is
set and an interrupt generated.
SYSTEM WAKE-UP
System wake-up can be initiated by any of four events:
A falling edge on the LIN pin
A wake-up signal from the AWD
A Logic [1] at Hall-effect sensor input pin during cyclic
check via AWD
An LVR condition
If one of these wake-up events occurs and the interrupt
mask bit for this event is set, the interrupt will wake-up the
microcontroller as well as the main voltage regulator (MREG)
(
Figure 8
).
發布緊急采購，3分鐘左右您將得到回復。