參數資料
型號： 78Q8430STEM#DB
廠商： Maxim Integrated Products
文件頁數： 43/88頁
文件大?。?/td> 0K
描述： EVAL BOARD 78Q8430
標準包裝： 1
系列： *
78Q8430 Data Sheet
DS_8430_001
48
Rev. 1.2
6.11.1.5 Signal Quality Error
In 10 Mbps mode, the MAC checks for a “heartbeat” at the end of a transmitted packet. This is a short
Collision signal within the first 40 bit times after end of transmission. Signal Quality Error sets the No
6.11.1.6 Deferral
In half duplex mode, during any attempt to send a packet, the MAC may have to defer the transmission
because of a pre-occupied network. This is not an error, but is used as a network activity indicator, but
only when collisions do not occur. Deferral sets the Deferral bit of the Transmit Packet Status Register
6.11.1.7 Excessive Deferral
In half duplex operation, the MAC will defer transmission of frames when there is network activity. If the
deferral time is longer than two maximum sized frame times (2.4288 ms for 10-Mbps operation or 0.24288
ms for 100-Mbps operation) then the Excessive Deferral bit of the Transmit Packet Status Register
(TPSR) is set. If the Tx Enable bit of the MCR Register (MCR) is clear, then the transmission is aborted.
Excessive deferral indicates a possible network problem.
6.11.2 MAC Receive Errors
6.11.2.1 Alignment Error
At the end of reception, the MAC receive block checks that the incoming packet has been correctly
framed on an 8-bit boundary. If it is not and the CRC is invalid, data has been disrupted through the
network and the MAC receive block reports an alignment error. A CRC error is also reported. The
Dangling Byte bit and the CRC bit are set in the Receive Packet Status Register (RPSR).
6.11.2.2 CRC Error
At the end of reception, the MAC receive block checks the CRC for validity and reports a CRC error if it is
invalid.
6.11.2.3 Overflow Error
During reception, incoming data is put into the MAC receive FIFO before it is transferred to the QUE
receive controller. If the MAC receive FIFO fills up because of excessive system latency or other
reasons, the MAC receive block sets the Overflow Error of the Receive Packet Status Register (RPSR)
and the remaining frame is dropped.
6.11.2.4 Length Error
The MAC receive block checks the length of the incoming packet at the end of reception based on the
value of the Len/Type field of the frame. If the length is specified in the Len/Type field and the frame is
longer than the maximum frame size of 1518 bytes, (1522 for VLAN tagged packets), the MAC receive
block reports a length error, unless long frame mode is enabled. The MAC will also flag as an error a
MAC control frame that is not exactly 64 bytes in length.
6.11.2.5 MII Error
The PHY informs the MAC if it detects a media error (such as coding violation) by asserting RX_ER.
When the PHY asserts RX_ER, the MAC sets the MII error bit in the Receive Packet Status Register
相關PDF資料
PDF描述
CM453232-470JL INDUCTOR 47UH 140MA SMD
CM453232-3R9JL INDUCTOR 3.9UH 330MA SMD
UPT2D221MHD CAP ALUM 220UF 200V 20% RADIAL
UVR2V470MHD CAP ALUM 47UF 350V 20% RADIAL
REC6-2415DRW/R8/A CONV DC/DC 6W 18-36VIN +/-15VOUT
相關代理商/技術參數
參數描述
78-R3 功能描述:3M SCOTCHCAST REENTERABLE SIGNAL 制造商:3m 系列:* 零件狀態:在售 標準包裝:1
78-R4 功能描述:3M SCOTCHCAST REENTERABLE SIGNAL 制造商:3m 系列:* 零件狀態:在售 標準包裝:1
78RB02 功能描述:SWITCH 2 POS DIP RECESSED UNSLD RoHS:否 類別:開關 >> DIP 系列:78 特色產品:RDM Series Rotary DIP Switch 標準包裝:70 系列:RDM 電路:十六進制 位置數:16 觸點額定電壓:0.1A @ 42VDC 觸動器類型:用于工具旋轉 觸動器電平:凹槽式 安裝類型:通孔 方向:頂部觸動 可清洗:是 其它名稱:EG4977-5RDMAR16PIT
78RB02RA 制造商:Grayhill 功能描述:DIP, 2 POS, FLUSH ACTUATOR, SPST, GOLD - Rail/Tube
78RB02RAT 功能描述:SWITCH DIP RECESSED 2POS UNSLD RoHS:是 類別:開關 >> DIP 系列:78 特色產品:RDM Series Rotary DIP Switch 標準包裝:70 系列:RDM 電路:十六進制 位置數:16 觸點額定電壓:0.1A @ 42VDC 觸動器類型:用于工具旋轉 觸動器電平:凹槽式 安裝類型:通孔 方向:頂部觸動 可清洗:是 其它名稱:EG4977-5RDMAR16PIT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*