參數資料
型號： 78P2253-IGT
廠商： Electronic Theatre Controls, Inc.
英文描述： XTAL CER SMT 11X5 4PAD
中文描述： 收發器
文件頁數： 11/23頁
文件大?。?/td> 107K
代理商： 78P2253-IGT
78P2253
E4/STM-1/STS-3/OC-3
Transceiver
11
ELECTRICAL SPECIFICATIONS
(continued)
Note 1
– The maximum “steady state” amplitude should not exceed the 0.55V limit. Overshoots and other transients are permitted to fall
into the shaded area bounded by the amplitude levels 0.55V and 0.6V, provided that they do not exceed the steady state level by more
than 0.05V.
Note 2
– For all measurements using these masks, the signal should be AC coupled, using a capacitor of not less than 0.01
μ
F, to the
input of the oscilloscope used for measurements. The nominal zero level for both masks should be aligned with the oscilloscope trace with
no input signal. With the signal then applied, the vertical position of the trace can be adjusted with the objective of meeting the limits of the
masks. Any such adjustment should be the same for both masks and should not exceed
±
0.05V. This may be checked by removing the
input signal again and verifying that the trace lies with
±
0.05V of the nominal zero level of the masks.
Note 3
– Each pulse in a coded pulse sequence should meet the limits of the relevant mask, irrespective of the state of the preceding or
succeeding pulses, with both pulse masks fixed in the same relation to a common timing reference, i.e. with their nominal start and finish
edges coincident. The masks allow for HF jitter caused by intersymbol interference in the output stage, but not for jitter present in the timing
signal associated with the source of the interface signal. When using an oscilloscope technique to determine pulse compliance with the
mask, it is important that successive traces of the pulses overlay in order to suppress the effects of low frequency jitter. This can be
accomplished by several techniques [e.g. a) triggering the oscilloscope on the measured waveform or b) providing both the oscilloscope
and the pulse output circuits with the same clock signal].
Note 4
– For the purpose of these masks, the rise time and decay time should be measured between –0.4V and 0.4V, and should not
exceed 2ns.
FIGURE 4 – MASK OF A PULSE CORRESPONDING TO A BINARY ZERO IN E4 MODE
(Note 1)
(Note 1)
(Note 1)
0.60
0.55
0.50
0.45
0.40
0.05
-0.05
-0.50
-0.55
-0.60
-0.45
-0.40
(Note 1)
0.35ns
Nominal
Zero Level
(Note 2)
T = 7.18ns
0.1ns
0.1ns
1ns
1.795 ns
1.795 ns
1.795 ns
1ns
1.795 ns
1ns
1ns
1ns
0.1ns
0.1ns
1ns
Nominal
Pulse
0.35ns
V
相關PDF資料
PDF描述
78P7200 Line Interface Unit
78P7200-IH Line Interface Unit
78P7200 E3/DS3/STS-1 Transceiver
78P7200L E3/DS3/STS-1 Transceiver
78P7200L-IGT E3/DS3/STS-1 Transceiver
相關代理商/技術參數
參數描述
78P2254 制造商:未知廠家 制造商全稱:未知廠家 功能描述:OC-3 / STM-1 / STS-3 / E4 Transceivers
78P2254-IGT 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecomm/Datacomm
78P2342-IGT 制造商:TERIDIAN 制造商全稱:TERIDIAN 功能描述:2-port E3/DS3/STS-1 LIU with Jitter Attenuator
78P2342-IGT/A07 制造商:TERIDIAN 制造商全稱:TERIDIAN 功能描述:2-port E3/DS3/STS-1 LIU with Jitter Attenuator
78P2342-IGT/F 制造商:Maxim Integrated Products 功能描述:LEAD FREE - Rail/Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*