參數資料
型號: 4571
廠商: Renesas Technology Corp.
英文描述: SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
中文描述: 單芯片4位微機的CMOS
文件頁數: 32/126頁
文件大?。?/td> 1627K
代理商: 4571
Rev.1.02
May 25, 2007
Page 13 of 124
REJ03B0179-0102
4571 Group
(5) Stack registers (SKS) and stack pointer (SP)
Stack registers (SKs) are used to temporarily store the contents of
program counter (PC) just before branching until returning to the
original routine when;
branching to an interrupt service routine (referred to as an
interrupt service routine),
performing a subroutine call, or
executing the table reference instruction (TABP p).
Stack registers (SKs) are eight identical registers, so that
subroutines can be nested up to 8 levels. However, one of stack
registers is used respectively when using an interrupt service
routine and when executing a table reference instruction.
Accordingly, be careful not to over the stack when performing
these operations together. The contents of registers SKs are
destroyed when 8 levels are exceeded.
The register SK nesting level is pointed automatically by 3-bit
stack pointer (SP). The contents of the stack pointer (SP) can be
transferred to register A with the TASP instruction.
Figure 11 shows the stack registers (SKs) structure.
Figure 12 shows the example of operation at subroutine call.
(6) Interrupt stack register (SDP)
Interrupt stack register (SDP) is a 1-stage register. When an
interrupt occurs, this register (SDP) is used to temporarily store
the contents of data pointer, carry flag, skip flag, register A, and
register B just before an interrupt until returning to the original
routine.
Unlike the stack registers (SKs), this register (SDP) is not used
when executing the subroutine call instruction and the table
reference instruction.
(7) Skip flag
Skip flag controls skip decision for the conditional skip
instructions and continuous described skip instructions. When an
interrupt occurs, the contents of skip flag is stored automatically
in the interrupt stack register (SDP) and the skip condition is
retained.
Fig 11. Stack registers (SKs) structure
Fig 12. Example of operation at subroutine call
Stack pointer (SP) points “7” at reset or returning
from RAM back-up mode. It points “0” by
executing the first BM instruction, and the
contents of program counter is stored in SK0.
When the BM instruction is executed after eight
stack registers are used ((SP) = 7), (SP) = 0 and
the contents of SK0 is destroyed.
Program counter (PC)
SK0
SK1
SK2
SK3
SK4
SK5
SK6
SK7
Executing BM
instruction
Executing RT
instruction
(SP) = 0
(SP) = 1
(SP) = 2
(SP) = 3
(SP) = 4
(SP) = 5
(SP) = 6
(SP) = 7
(SP)
0
(SK0)
000116
(PC)
SUB1
(PC)
(SK0)
(SP)
7
Main program
Address
000016 NOP
000116 BM SUB1
000216 NOP
SUB1:
NOP
RT
Subroutine
Note : Returning to the BM instruction execution
address with the RT instruction, and the BM
instruction becomes the NOP instruction.
相關PDF資料
PDF描述
45722.123.242 1 mm2, COPPER ALLOY, WIRE TERMINAL
45733.201.004 2.5 mm2, COPPER ALLOY, WIRE TERMINAL
45733.417.031 2.5 mm2, WIRE TERMINAL
45744.123.211 6 mm2, COPPER ALLOY, WIRE TERMINAL
45744.201.004 6 mm2, COPPER ALLOY, WIRE TERMINAL
相關代理商/技術參數
參數描述
4571_08 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:Standard Characteristics
45-710 制造商:GC Electronics 功能描述:EXTENSION CABLE, PARALLEL, 6FT, PUTTY; Cable Length - Imperial:6ft; Cable Length - Metric:1.83m; Connector Type A:Centronics 36 Position Plug; Connector Type B:Centronics 36 Position Receptacle; Jacket Color:Putty; Cable Color:Putty 制造商:Calrad Electronics 功能描述:Cable Assembly Parallel 6m 28AWG 36 POS SCSI to 36 POS SCSI M-F
4-571011-3 功能描述:ANVIL 制造商:te connectivity amp connectors 系列:* 零件狀態:有效 標準包裝:1
457102-1 制造商:TE Connectivity 功能描述:BLOCK, PLATE MTG - Bulk
45710224PTC2103 制造商:Omron Corporation 功能描述: