- 您現在的位置：買賣IC網 > PDF目錄368957 > 28F400BL-T 4-MBlT (256K x 16. 512K x 8) LOW-POWER BOOT BLOCK FLASH MEMORY FAMILY PDF資料下載
參數資料
| 型號： | 28F400BL-T |
| 英文描述： | 4-MBlT (256K x 16. 512K x 8) LOW-POWER BOOT BLOCK FLASH MEMORY FAMILY |
| 中文描述： | 4 MBlT（256K × 16。為512k × 8）低功耗啟動塊閃存系列 |
| 文件頁數： | 10/44頁 |
| 文件大?。?/td> | 496K |
| 代理商： | 28F400BL-T |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
28F400BL-T/B, 28F004BL-T/B
1.6 Pin Descriptions for x8 28F004BL
Symbol
Type
Name and Function
A
0
–A
18
I
ADDRESS INPUTS
for memory addresses. Addresses are internally latched during
a write cycle.
A
9
I
ADDRESS INPUT:
When A
9
is at 12V the signature mode is accessed. During this
mode A
0
decodes between the manufacturer and device ID’s.
DATA INPUTS/OUTPUTS:
Inputs array data on the second CE
Y
and WE
Y
cycle
during a program command. Inputs commands to the command user interface
when CE
Y
and WE
Y
are active. Data is internally latched during the write and
program cycles. Outputs array, Intelligent Identifier and status register data. The
data pins float to tri-state when the chip is deselected or the outputs are disabled.
DQ
0
–DQ
7
I/O
CE
Y
I
CHIP ENABLE:
Activates the device’s control logic, input buffers, decoders and
sense amplifiers. CE
Y
is active low; CE
Y
high deselects the memory device and
reduces power consumption to standby levels.
RP
Y
I
RESET/DEEP POWER-DOWN:
Provides Three-State control. Puts the device in
deep power-down mode. Locks the Boot Block from program/erase.
When RP
Y
is at logic high level and equals 4.1V maximum the Boot Block is locked
and cannot be programmed or erased.
When RP
Y
e
11.4V minimum the Boot Block is unlocked and can be programmed
or erased.
When RP
Y
is at a logic low level the Boot Block is locked, the deep power-down
mode is enabled and the WSM is reset preventing any blocks from being
programmed or erased, therefore providing data protection during power
transitions. When RP
Y
transitions from logic low to logic high, the flash memory
enters the read-array mode.
OE
Y
I
OUTPUT ENABLE:
Gates the device’s outputs through the data buffers during a
read cycle. OE
Y
is active low.
WE
Y
I
WRITE ENABLE:
Controls writes to the Command Register and array blocks. WE
Y
is active low. Addresses and data are latched on the rising edge of the WE
Y
pulse.
V
PP
PROGRAM/ERASE POWER SUPPLY:
For erasing memory array blocks or
programming data in each block.
Note:
V
PP
k
V
PPLMAX
memory contents cannot be altered.
V
CC
DEVICE POWER SUPPLY (3.3V
g
0.3V, 5V
g
10%)
GND
GROUND:
For all internal circuitry.
NC
NO CONNECT:
Pin may be driven or left floating.
DU
DON’T USE PIN:
Pin should not be connected to anything.
10
相關PDF資料 |
PDF描述 |
|---|---|
| 28F400BV-B | 4-MBIT (256K X 16. 512K X 8) SmartVoltage BOOT BLOCK FLASH MEMORY FAMILY |
| 28F400BV-T | 4-MBIT (256K X 16. 512K X 8) SmartVoltage BOOT BLOCK FLASH MEMORY FAMILY |
| 28F400BX-B | 4-MBIT (256K X 16. 512K X 8) BOOT BLOCK FLASH MEMORY FAMILY |
| 28F400BX-T | 4-MBIT (256K X 16. 512K X 8) BOOT BLOCK FLASH MEMORY FAMILY |
| 28F800B5 | Dual-Slot, PCMCIA Analog Power Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 28F400BL-TB | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:4-MBlT (256K x 16, 512K x 8) LOW-POWER BOOT BLOCK FLASH MEMORY FAMILY |
| 28F400BV-B | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:4-MBIT (256K X 16. 512K X 8) SmartVoltage BOOT BLOCK FLASH MEMORY FAMILY |
| 28F400BV-T | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:4-MBIT (256K X 16. 512K X 8) SmartVoltage BOOT BLOCK FLASH MEMORY FAMILY |
| 28F400BV-T/B | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Book Block Flash Memory F |
| 28F400BV-TB | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:4-MBIT (256K X 16, 512K X 8)SmartVoltage BOOT BLOCK FLASH MEMORY FAMILY |
發布緊急采購，3分鐘左右您將得到回復。