參數資料
型號： μPD75F4246(A)
廠商： NEC Corp.
元件分類： 8位微控制器
英文描述： 8 Bit Single Chip Microcontrollers
中文描述： 8位單片機微控制器
文件頁數： 24/143頁
文件大?。?/td> 549K
代理商： ΜPD75F4246(A)
12
CHAPTER 2 BASIC FORMAT
2.7 List of Commands
Table 2-2. List of Commands
Command
Command Name
Description of Processing
00H
Reset command
This command initializes the
μ
PD75F4264’s mode and to confirm synchronization
detection as part of synchronization detection processing.
90H
Oscillation frequency setting
command
This command notifies the
μ
PD75F4264 concerning its operating clock. The
μ
PD75F4264 internally uses this frequency value as the basic frequency value for
calculating the write time, erase time, etc.
95H
Erase time setting command
This command sends the
μ
PD75F4264’s erase time to the
μ
PD75F4264.
20H
Erase command
This command erases the
μ
PD75F4264’s program area (flash memory).
40H
High-speed write command
This command writes data to the
μ
PD75F4264’s program area (flash memory). It
is used in combination with the status check command to check for write failures
while the write operation is in progress.
44H
Continuous write command
This command writes to the address following the last address written to via the high-
speed write command. This format eliminates the need to transfer the “write start
address” and “transfer byte count” from the high-speed write command.
11H
Verify command
This command compares the contents of the
μ
PD75F4264’s program area (flash
memory) with the data received by the
μ
PD75F4264.
30H
Blank check command
This command checks whether or not the
μ
PD75F4264’s program area (flash
memory) has been erased.
80H
High-speed read command
This command reads the
μ
PD75F4264’s EEPROM data. It is used in combination
with the status check command to check for read failures while the read operation
is in progress.
88H
Continuous read command
This command reads from the address following the last address to be read via the
high-speed read command. This format eliminates the need to transfer the “read
start address” and “receive byte count” from the high-speed read command.
C0H
Silicon signature command
This command gets the
μ
PD75F4264’s device information (silicon signature).
70H
Status check command
This command gets the
μ
PD75F4264’s internal command execution status.
相關PDF資料
PDF描述
μPD75F4246 8 Bit Single Chip Microcontrollers
μPD75F4246A 8 Bit Single Chip Microcontrollers
μPD75P0116 4 Bit RISC Microcontrollers(4 位單片微控制器)
μPD75P3116 4 Bit Single Chip Microcontrollers(4位單片微控制器)
μPD75P3216 4 Bit Single Chip Microcontrollers(4位單片微控制器)
相關代理商/技術參數
參數描述
PD75G6FK13 制造商:American Power Conversion Corp (APC by Schneider Electric) 功能描述:75KVA PDU W/ 480 PRI 208/120 SEC K13 RATED XMER 制造商:Schneider Electric 功能描述:APC 75KVA PDU W/ 480 PRI 20 - Bulk
PD75R-103K 功能描述:固定電感器 10uH 10% .08ohm Choke SMT Power Ind RoHS:否 制造商:AVX 電感:10 uH 容差:20 % 最大直流電流:1 A 最大直流電阻:0.075 Ohms 工作溫度范圍:- 40 C to + 85 C 自諧振頻率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接類型:SMD/SMT 封裝 / 箱體:6.6 mm x 4.45 mm
PD75R-104K 功能描述:固定電感器 100uH 10% .5ohm Choke SMT Power Ind RoHS:否 制造商:AVX 電感:10 uH 容差:20 % 最大直流電流:1 A 最大直流電阻:0.075 Ohms 工作溫度范圍:- 40 C to + 85 C 自諧振頻率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接類型:SMD/SMT 封裝 / 箱體:6.6 mm x 4.45 mm
PD75R-104K/R500 制造商:API Delevan 功能描述:PD75R series 100 uH 10 % 740 mA SMT Power Choke
PD75R-123K 功能描述:固定電感器 12uH 10% .085ohm Choke SMT Power Ind RoHS:否 制造商:AVX 電感:10 uH 容差:20 % 最大直流電流:1 A 最大直流電阻:0.075 Ohms 工作溫度范圍:- 40 C to + 85 C 自諧振頻率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接類型:SMD/SMT 封裝 / 箱體:6.6 mm x 4.45 mm
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*