參數資料
型號： μPD75F4246(A)
廠商： NEC Corp.
元件分類： 8位微控制器
英文描述： 8 Bit Single Chip Microcontrollers
中文描述： 8位單片機微控制器
文件頁數： 21/143頁
文件大?。?/td> 549K
代理商： ΜPD75F4246(A)
9
CHAPTER 2 BASIC FORMAT
2.4 Synchronization Detection Processing
Synchronization detection processing is a type of processing whose purpose is to confirm whether or not the
μ
PD75F4264 can operate normally after it has been switched to flash memory write mode. It does this by checking
how the
μ
PD75F4264 responds after the flash writer sends a command to it.
Figure 2-3. Flow of Synchronization Detection Processing
Note
ACK: Acknowledge
This signal (3CH) indicates when the
μ
PD75F4264’s processing ends normally.
A different signal (“NACK”) indicates when a processing fault has occurred (a “NACK” judgment is made
whenever a value other than “3CH” is returned at the timing for receiving the ACK signal).
2.4.1 Initialization wait time
After the
μ
PD75F4264 has been switched to flash memory write mode, the flash writer must wait (“initialization
wait”) until the
μ
PD75F4264’s programming firmware has been initialized and is ready to operate. This initialization
wait time must be at least as long as the
μ
PD75F4264’s oscillation wait time plus the time needed for the programming
firmware to initialize the
μ
PD75F4264 itself. For details of minimum initialization wait times, see
CHAPTER 6
μ
PD75F4264 PROGRAMMING CHARACTERISTICS (PRELIMINARY)
.
2.4.2 Synchronization check processing
The
μ
PD75F4264 uses synchronization check processing to determine whether or not the setup for communication
and write operations has been completed. Specifically, this processing checks whether or not an ACK signal was
returned after the flash writer sent a reset command to the
μ
PD75F4264. Up to 16 command send retries are permitted,
so that if an ACK is sent from the
μ
PD75F4264 within 16 retries, it is confirmed that the
μ
PD75F4264 is ready for
programming. For description of the reset command’s format, see
CHAPTER 4 SAMPLE PROGRAMS
.
Synchronization
detection
End
(Normal end)
End
(Synchronization detection failed)
Wait processing for
PD75F4264 initialization
μ
Send reset command (00H)
NO
NO
YES
YES
Receive ACK
Note
Retry 16 times
··· See
2.4.1 Initialization wait time.
··· See
2.4.2 Synchronization check
processing.
相關PDF資料
PDF描述
μPD75F4246 8 Bit Single Chip Microcontrollers
μPD75F4246A 8 Bit Single Chip Microcontrollers
μPD75P0116 4 Bit RISC Microcontrollers(4 位單片微控制器)
μPD75P3116 4 Bit Single Chip Microcontrollers(4位單片微控制器)
μPD75P3216 4 Bit Single Chip Microcontrollers(4位單片微控制器)
相關代理商/技術參數
參數描述
PD75G6FK13 制造商:American Power Conversion Corp (APC by Schneider Electric) 功能描述:75KVA PDU W/ 480 PRI 208/120 SEC K13 RATED XMER 制造商:Schneider Electric 功能描述:APC 75KVA PDU W/ 480 PRI 20 - Bulk
PD75R-103K 功能描述:固定電感器 10uH 10% .08ohm Choke SMT Power Ind RoHS:否 制造商:AVX 電感:10 uH 容差:20 % 最大直流電流:1 A 最大直流電阻:0.075 Ohms 工作溫度范圍:- 40 C to + 85 C 自諧振頻率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接類型:SMD/SMT 封裝 / 箱體:6.6 mm x 4.45 mm
PD75R-104K 功能描述:固定電感器 100uH 10% .5ohm Choke SMT Power Ind RoHS:否 制造商:AVX 電感:10 uH 容差:20 % 最大直流電流:1 A 最大直流電阻:0.075 Ohms 工作溫度范圍:- 40 C to + 85 C 自諧振頻率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接類型:SMD/SMT 封裝 / 箱體:6.6 mm x 4.45 mm
PD75R-104K/R500 制造商:API Delevan 功能描述:PD75R series 100 uH 10 % 740 mA SMT Power Choke
PD75R-123K 功能描述:固定電感器 12uH 10% .085ohm Choke SMT Power Ind RoHS:否 制造商:AVX 電感:10 uH 容差:20 % 最大直流電流:1 A 最大直流電阻:0.075 Ohms 工作溫度范圍:- 40 C to + 85 C 自諧振頻率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接類型:SMD/SMT 封裝 / 箱體:6.6 mm x 4.45 mm
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*