JITTER
參數資料
型號： XRT75VL00DIVTR
廠商： Exar Corporation
文件頁數： 33/92頁
文件大?。?/td> 0K
描述： IC LIU E3/DS3/STS-1 1CH 52TQFP
標準包裝： 1,000
類型： 線路接口裝置（LIU）
驅動器/接收器數： 1/1
規程： DS3，E3，STS-1
電源電壓： 3.135 V ~ 3.465 V
安裝類型： 表面貼裝
封裝/外殼： 52-LQFP
供應商設備封裝： 52-TQFP（10x10）
包裝： 帶卷 (TR)
XRT75VL00D
34
REV. 1.0.4
E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
6.2
JITTER TRANSFER - RECEIVER/TRANSMITTER:
Jitter Transfer function is defined as the ratio of jitter on the output relative to the jitter applied on the input
versus frequency.
There are two distinct characteristics in jitter transfer: jitter gain (jitter peaking) defined as the highest ratio
above 0 dB; and jitter transfer bandwidth.The overall jitter transfer bandwidth is controller by a low bandwidth
loop,which is part of the XRT75VL00D.
The jitter transfer function is a ratio between the jitter output and jitter input for a component, or system often
expressed in dB. A negative dB jitter transfer indicates the element removed jitter. A positive dB jitter transfer
indicates the element added jitter.A zero dB jitter transfer indicates the element had no effect on jitter.
Table 12 shows the jitter transfer characteristics and/or jitter attenuation specifications for various data rates:
The XRT75VL00D meets the above Jitter Specifications.
6.3
JITTER GENERATION:
Jitter Generation is defined as the process whereby jitter appears at the output port of the digital equipment in
the absence of applied input jitter. Jitter Generation is measured by sending jitter free data to the clock and
data recovery circuit and measuring the amount of jitter on the output clock or the re-timed data. Since this is
essentially a noise measurement, it requires a definition of bandwidth to be meaningful. The bandwidth is set
according to the data rate. In general, the jitter is measured over a band of frequencies.
6.4
Jitter Attenuator:
An advanced crystal-less jitter attenuator is included in the XRT75VL00D. The jitter attenuator uses the internal
reference clock.
In Host mode, by clearing or setting the JATx/Rx bit in the control register selects the jitter attenuator either in
the Receive or Transmit path. In Hardware mode, JATx/Rx pin selects the jitter attenuator in Receive or
Transmit path.
The FIFO is either a 16-bit, 32-bit or 128-bit register. In Host mode, the bits JA0 and JA1can be set to
appropriate combination to select the different FIFO sizes or to disable the jitter attenuator. In Hardware mode,
appropriate setting of the pins JA0 and JA1 selects the different FIFO sizes or disable the jitter attenuator. Data
is clocked into the FIFO with the associated clock signal (TxClk or RxClk) and clocked out of the FIFO with the
TABLE 11: JITTER AMPLITUDE VERSUS MODULATION FREQUENCY (JITTER TOLERANCE)
BIT RATE
(KB/S)
STANDARD
INPUT JITTER AMPLITUDE (UI
P
-P)
MODULATION FREQUENCY
A1
A2
A3
F
1(HZ)
F
2(HZ)
F
3(KHZ)
F
4(KHZ)
F
5(KHZ)
34368
ITU-T G.823
1.5
0.15
-
100
1000
10
800
-
44736
GR-499
CORE Cat I
5
0.1
-
10
2.3k
60
300
-
44736
GR-499
CORE Cat II
10
0.3
-
10
669
22.3
300
-
51840
GR-253
CORE Cat II
15
1.5
0.15
10
30
300
2
20
TABLE 12: JITTER TRANSFER SPECIFICATIONS
E3
DS3
STS-1
ETSI TBR-24
GR-499 CORE section 7.3.2
Category I and Category II
GR-253 CORE section 5.6.2.1
相關PDF資料
PDF描述
MS27468T9B35S EDR CONN RCPT 6POS JAM NUT W/SCKT
MS27466T23B35SD CONN RCPT 100POS WALL MNT W/SCKT
MS27466E15A35P CONN RCPT 37POS WALL MNT W/PINS
VI-B40-IV-F1 CONVERTER MOD DC/DC 5V 150W
MS27497T10B5PA CONN RCPT 5POS WALL MNT W/PINS
相關代理商/技術參數
參數描述
XRT75VL00DIVTR-F 功能描述:時鐘合成器/抖動清除器 3.3V 1 CH E3/DS3/STS W/SONET DE-SYNCH RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT75VL00ES 功能描述:時鐘合成器/抖動清除器 1CHT3/E3/STS1LIU+A 3.3V VOLTAGE DRIVE RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT75VL00IV 功能描述:外圍驅動器與原件 - PCI 3.3V 1 CH E3/DS3/STS W/JITTER ATTEN RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
XRT75VL00IV-F 功能描述:外圍驅動器與原件 - PCI 3.3V 1 CH E3/DS3/STS W/JITTER ATTEN RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
XRT75VL00IVTR 功能描述:時鐘合成器/抖動清除器 3.3V 1 CH E3/DS3/STS W/JITTER ATTEN RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*