參數資料
型號： XRT75R12D
廠商： Exar Corporation
英文描述： TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
中文描述： 第十二章通道E3/DS3/STS-1線路接口單元與SONET DESYNCHRONIZER
文件頁數： 120/131頁
文件大小： 717K
代理商： XRT75R12D
XRT75R12D
REV. P1.0.1
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
PRELIMINARY
115
Using a particular clock edge within the "gapped" clock signal (from the Mapper IC) to sample and latch the
value of each DS3 data-bit that is output from the Mapper IC.
To (through the user of the Jitter Attenuator block) attenuate the jitter within this "DS3 data" and "clock signal"
that is output from the Mapper IC.
To convert this "smoothed" DS3 data and clock into industry-compliant DS3 pulses, and to output these
pulses onto the line.
To configure the LIU to operate in the correct mode for this application, the user must execute the following
configuration steps.
a. Configure the LIU to operate in the DS3 Mode
The user can configure a given channel (within the LIU) to operate in the DS3 Mode, by executing either of the
following steps.
If the LIU has been configured to operate in the Host Mode
The user can accomplish this by setting both Bits 2 (E3_n) and Bits 1 (STS-1/DS3*_n), within each of the
"Channel Control Registers" to "0" as depicted below.
If the LIU has been configured to operate in the Hardware Mode
The user can accomplish this by pulling all of the following input pins "Low".
Pin 76 - E3_0
Pin 94 - E3_1
Pin 85 - E3_2
Pin 72 - STS-1/DS3_0
Pin 98 - STS-1/DS3_1
Pin 81 - STS-1/DS3_2
b. Configure the LIU to operate in the Single-Rail Mode
Since the Mapper IC will typically output a single "Data Line" and a "Clock Line" for each DS3 signal that it
demaps from the incoming STS-N signal, it is imperative to configure each channel within the LIU to operate in
the Single Rail Mode.
The user can accomplish this by executing either of the following steps.
If the LIU has been configured to operate in the Host Mode
The user can accomplish this by setting Bit 0 (SR/DR*), within the each of the "Channel Control" Registers to
1, as illustrated below.
CHANNEL CONTROL REGISTER - CHANNEL 0 ADDRESS LOCATION = 0X06
CHANNEL 1 ADDRESS LOCATION = 0X0E
CHANNEL 2 ADDRESS LOCATION = 0X16
B
IT
7
B
IT
6
B
IT
5
B
IT
4
B
IT
3
B
IT
2
B
IT
1
B
IT
0
Unused
PRBS Enable
Ch_n
RLB_n
LLB_n
E3_n
STS-1/DS3_n
SR/DR_n
R/O
R/O
R/W
R/W
R/W
R/W
R/W
R/W
0
0
0
0
0
0
0
0
相關PDF資料
PDF描述
XRT75R12DIB TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
XRT75R12 TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
XRT75R12IB TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
XRT75VL00 E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
XRT75VL00IV E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
相關代理商/技術參數
參數描述
XRT75R12D_06 制造商:EXAR 制造商全稱:EXAR 功能描述:TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET
XRT75R12D_07 制造商:EXAR 制造商全稱:EXAR 功能描述:TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET
XRT75R12DES 功能描述:時鐘合成器/抖動清除器 RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT75R12DIB 功能描述:網絡控制器與處理器 IC 12CH E3/DS3/STS W/JITTER R3 TECH RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
XRT75R12DIB-F 功能描述:網絡控制器與處理器 IC 12 Channel 3.3V-5V temp -45 to 85C RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*