- 您現在的位置：買賣IC網 > PDF目錄1977 > XRT75L03DIV-F (Exar Corporation)IC LIU E3/DS3/STS-1 3CH 128LQFP PDF資料下載
參數資料
| 型號： | XRT75L03DIV-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 19/134頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC LIU E3/DS3/STS-1 3CH 128LQFP |
| 標準包裝： | 72 |
| 類型： | 線路接口裝置（LIU） |
| 驅動器/接收器數： | 3/3 |
| 規程： | DS3，E3，STS-1 |
| 電源電壓： | 3.135 V ~ 3.465 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 128-LQFP 裸露焊盤 |
| 供應商設備封裝： | 128-LQFP（14x20） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁
á
XRT75L03D
THREE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
REV. 1.0.0
110
In this application, these Mapper devices can be thought of as multi-channel devices. For example, an STS-3
Mapper can be viewed as a 3-Channel DS3/STS-1 to STS-3 Mapper IC. Similarly, an STS-12 Mapper can be
viewed as a 12-Channel DS3/STS-1 to STS-12 Mapper IC. Continuing on with this line of thought, if a Mapper
IC is configured to receive an STS-N signal, and (from this STS-N signal) de-map and output N DS3 signals
(towards the DS3 facility), then it will typically do so in the following manner.
In many cases, the Mapper IC will output this DS3 signal, using both a "Data-Signal" and a "Clock-Signal". In
many cases, the Mapper IC will output the contents of an entire STS-1 data-stream via the Data-Signal.
However, as the Mapper IC output this STS-1 data-stream, it will typically supply clock pulses (via the Clock-
Signal output) coincident to whenever a DS3 bit is being output via the Data-Signal. In this case, the Mapper
IC will NOT supply a clock pulse coincident to when a TOH, POH, or any "non-DS3 data-bit" is being output
via the "Data-Signal".
Now, since the Mapper IC will output the entire STS-1 data stream (via the Data-Signal), the output Clock-
Signal will be of the form such that it has a period of 19.3ns (e.g., a 51.84MHz clock signal). However, the
Mapper IC will still generate approximately 44,736,000 clock pulses during any given one second period.
Hence, the clock signal that is output from the Mapper IC will be a horribly gapped 44.736MHz clock signal.
One can view such a clock signal as being a very-jittery 44.736MHz clock signal. This jitter that exists within
the "Clock-Signal" is referred to as "Clock-Gapping" Jitter. A more detailed discussion on how the user must
handle this type of jitter is presented in “Section 9.8.2, Recommendations on Pre-Processing the Gapped
9.5
A Review of the Category I Intrinsic Jitter Requirements (per Telcordia GR-253-CORE) for DS3
applications
The "Category I Intrinsic Jitter Requirements" per Telcordia GR-253-CORE (for DS3 applications) mandates
that the user perform a large series of tests against certain specified "Scenarios". These "Scenarios" and their
corresponding requirements is summarized in Table 31, below.
TABLE 31: SUMMARY OF "CATEGORY I INTRINSIC JITTER REQUIREMENT PER TELCORDIA GR-253-CORE, FOR DS3
APPLICATIONS
SCENARIO
DESCRIPTION
SCENARIO
NUMBER
TELCORDIA GR-253-CORE
CATEGORY I INTRINSIC
JITTER REQUIREMENTS
COMMENTS
DS3 De-Mapping
Jitter
0.4UI-pp
Includes effects of De-Mapping and Clock Gapping Jitter
Single Pointer
Adjustment
A1
0.3UI-pp + Ao
Includes effects of Jitter from Clock-Gapping, De-Map-
ping and Pointer Adjustments.NOTE: Ao is the amount
of intrinsic jitter that was measured during the "DS3 De-
Mapping Jitter" phase of the Test.
Pointer Bursts
A2
1.3UI-pp
Includes effects of Jitter from Clock-Gapping, De-Map-
ping and Pointer Adjustments.
Phase Transients
A3
1.2UI-pp
Includes effects of Jitter from Clock-Gapping, De-Map-
ping and Pointer Adjustments.
87-3 Pattern
A4
1.0UI-pp
Includes effects of Jitter from Clock-Gapping, De-Map-
ping and Pointer Adjustments.
87-3 Add
A5
1.3UI-pp
Includes effects of Jitter from Clock-Gapping, De-Map-
ping and Pointer Adjustments.
87-3 Cancel
A5
1.3UI-pp
Includes effects of Jitter from Clock-Gapping, De-Map-
ping and Pointer Adjustments.
相關PDF資料 |
PDF描述 |
|---|---|
| XRT75L03IV-F | IC LIU E3/DS3/STS-1 3CH 128LQFP |
| XRT75L04DIV-F | IC LIU E3/DS3/STS-1 4CH 176TQFP |
| XRT75L04IV-F | IC LIU E3/DS3/STS-1 4CH 176LQFP |
| XRT75L06DIB-F | IC LIU E3/DS3/STS-1 6CH 217BGA |
| XRT75L06IB-F | IC LIU E3/DS3/STS-1 6CH 217BGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT75L03DIVTR | 功能描述:時鐘合成器/抖動清除器 3CHNNEL E3/DS3/STS 1 SONET DE-SYNCH RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel |
| XRT75L03DIVTR-F | 功能描述:接口 - 專用 RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| XRT75L03ES | 功能描述:時鐘合成器/抖動清除器 3 CH T3/E3/STS1 LIU+JA 3.3V RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel |
| XRT75L03IV | 功能描述:外圍驅動器與原件 - PCI 3CH E3/DS3/STS1 JITTER ATTENUATOR RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| XRT75L03IV-F | 功能描述:外圍驅動器與原件 - PCI 3-Ch DS3, E3, STS-1 RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。