參數資料
| 型號： | XRT7300IV |
| 廠商： | Exar Corporation |
| 文件頁數： | 19/55頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC LIU E3/DS3/STS-1 SGL 44TQFP |
| 標準包裝： | 160 |
| 類型： | 線路接口裝置（LIU） |
| 驅動器/接收器數： | 1/1 |
| 規程： | DS3，E3，STS-1 |
| 電源電壓： | 4.75 V ~ 5.25 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 44-LQFP |
| 供應商設備封裝： | 44-TQFP（10x10） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁
XRT7300
E3/DS3/STS-1 LINE INTERFACE UNIT
REV. 1.1.2
22
The XRT7300 Transmit Clock Duty Cycle Adjust cir-
cuit alleviates the need to supply a signal with a 50%
duty cycle to the TCLK input pin.
2.3
THE HDB3/B3ZS ENCODER BLOCK
The purpose of the HDB3/B3ZS Encoder Block is to
aid in the Clock Recovery process (at the Remote
Terminal Equipment) by ensuring an upper limit on
the number of consecutive zeros that can exist in the
line signal.
2.3.1
B3ZS Encoding
If the XRT7300 is configured to operate in the DS3 or
SONET STS-1 Modes, then the HDB3/B3ZS Encoder
block operates in the B3ZS Mode. When the Encod-
er is operating in this mode, it parses through and
searches the Transmit Binary Data Stream (from the
Transmit Logic Block) for the occurrence of three (3)
consecutive zeros (“000”). If the B3ZS Encoder finds
an occurrence of three consecutive zeros, it substi-
tutes these three “0’s” with either a "00V" or a "B0V"
pattern.
“B” represents a Bipolar pulse that is compliant with
the Alternating Polarity requirements of the AMI (Al-
ternate Mark Inversion) line code and “V” represents
a bipolar Violation (e.g., a bipolar pulse that violates
the Alternating Polarity requirements of the AMI line
code).
The B3ZS Encoder decides whether to substitute
with either a "00V" or a "B0V" pattern in order to in-
sure that an odd number of bipolar pulses exist be-
tween any two consecutive violation pulses.
Figure 13 illustrates the B3ZS Encoder at work with
two separate strings of three (or more) consecutive
zeros.
2.3.2
HDB3 Encoding
If the XRT7300 is configured to operate in the E3
Mode, then the HDB3/B3ZS Encoder block operates
in the HDB3 Mode. When the Encoder is operating in
this mode, it parses through and searches the Trans-
mit Data Stream (from the Transmit Logic Block) for
the occurrence of four (4) consecutive zeros (“0000”).
If the HDB3 Encoder finds an occurrence of four con-
secutive zeros, then it substitutes these four “0’s” with
either a “000V” or a “B00V” pattern in order to insure
that an odd number of bipolar pulses exist between
any two consecutive violation pulses.
FIGURE 13. AN EXAMPLE OF B3ZS ENCODING
Data
TPDATA
TNDATA
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0 0
V
Line Signal
B
0 V
TCLK
相關PDF資料 |
PDF描述 |
|---|---|
| XRT83SL216IB-F | IC LIU SH E1 16CH 289STBGA |
| XRT83SL28IV-F | IC LIU SH E1 8CH 144TQFP |
| XRT83SL30IV-F | IC LIU T1/E1/J1 SGL 64TQFP |
| XRT83SL314IB-L | IC LIU SH T1/E1/J1 14CH 304TBGA |
| XRT83SL34IV-F | IC LIU T1/E1/J1 QUAD 128TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT7300IV-F | 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| XRT7300IVTR | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| XRT7300IVTR-F | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| XRT7302IV | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:PCM Transceiver |
| XRT73L00 | 制造商:EXAR 制造商全稱:EXAR 功能描述:E3/DS3/STS-1 LINE INTERFACE UNIT |
發布緊急采購，3分鐘左右您將得到回復。