參數資料
型號： XRD98L62
廠商： Exar Corporation
英文描述： CCD Image Digitizers with CDA，PGS and 12-Bit A/D(CCD圖像數字轉換器（帶CDA，PGS和12位A/D轉換器）)
中文描述： 與綜合發展區，和12的PGS CCD圖像數字轉換器，位A / D（防治荒漠化公約圖像數字轉換器（帶地帶素類和12位的A / D轉換器））
文件頁數： 30/37頁
文件大小： 394K
代理商： XRD98L62
XRD98L62
30
Rev. P2.00
Preliminary
Line Rate Clocks
CLAMP & CAL are the two line rate clock signals.
There are two modes of operation for these clocks.
CAL & CLAMP Mode
In this mode the CLAMP signal is used to activate the
DC restore Clamp at the CDS input, and the CAL signal
is used to define the Optical Black pixels to be used for
the Black Level calibration function. Typically the
CLAMP pulse comes during the dummy or optical
black pixels at the beginning of each scan line, and the
CAL pulse comes during the longer string of optical
black pixels at the end of each scan line. CLAMP &
CAL must not be active at the same time.
In this mode there is an option to disconnect the CDS
from the input pins during the Vertical Shift time. To
enable this option write a “1” to the VSreject bit in the
Clock register. To properly define the Vertical Shift time
you must set the ClampCal bit properly.
In the typical case, the CCD has a few OB pixels at the
beginning of a line (CLAMP time) and a larger number
of OB pixels at the end of a scan line (CAL time). In this
case set the ClampCal bit = 0, this will define the
Vertical shift time as the time from the end of the CAL
pulse to the beginning of the CLAMP pulse.
If a CCD has more OB pixels at the beginning of a line,
then CAL should be active during these pixels and
CLAMP should be active at the end of the line. In this
case, set the ClampCal bit = 1, this will define the
Vertical shift time as the time from the end of the
CLAMP pulse to the beginning of the CAL pulse.
The ClampCal bit is also used by the Calibration logic.
If ClampCal is set as defined above, it should be correct
for the Calibration logic as well.
End of Line N
Start of Line N+1
Active Video
Pixels
OB pixels
Vertical Shift
Dummy &
OB pixels
CAL
(Black Level)
CLAMP
(DC restore)
CCD
Signal
Active Video pixels
t
CAL
t
CLAMP
Vert. Shift Reject
(internal)
Disconnect CDS from
input pins
Figure 20. Line Rate Timing with OneShot=0, VSreject=1 & ClampCal=0
相關PDF資料
PDF描述
XRDAN28 Frequency Response Effects of Overampling and Averaging on A/D Output Data
XRDAN29 Criteria for Accurate Sampling of Analog Signals
XRDAN30 CMOS Current Output D/A Converter Design Concepts for Wide Bandwidth Applications
XRK32308_07 3.3V ZERO DELAY BUFFER
XRK32308CD-1 3.3V ZERO DELAY BUFFER
相關代理商/技術參數
參數描述
XRD98L62ACV 制造商:EXAR 制造商全稱:EXAR 功能描述:CCD Image Digitizers with CDS, PGA and 12-Bit A/D
XRD98L62ACV-F 功能描述:視頻 IC RoHS:否 制造商:Fairchild Semiconductor 工作電源電壓:5 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-28 封裝:Reel
XRD98L62EVAL 功能描述:數據轉換 IC 開發工具 XRD98L62 EVAL BOARD RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V
XRD98L62ZEVAL 功能描述:數據轉換 IC 開發工具 Eval Board (Solder) XRD98L62AIV RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V
XRD98L63 制造商:EXAR 制造商全稱:EXAR 功能描述:CCD Image Digitizers with CDS, PGA and 12-Bit A/D
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*