- 您現在的位置：買賣IC網 > PDF目錄16988 > XRD98L61ZEVAL (Exar Corporation)EVAL BOARD FOR XRD98L61AIV PDF資料下載
參數資料
| 型號： | XRD98L61ZEVAL |
| 廠商： | Exar Corporation |
| 文件頁數： | 26/38頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVAL BOARD FOR XRD98L61AIV |
| 標準包裝： | 1 |
| 系列： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁
XRD98L61
32
Rev. 2.00
End of Line N
Start of Line N+1
Active Video
Pixels
OB pixels
Vertical Shift
Dummy &
OB pixels
CAL
Internal
DC restore time
CCD
Signal
Active Video pixels
t
CAL
4 pixels
CLAMP
(vertical shift)
Disconnect CDS from
input pins
Internal Black Level
calibration time
t
CAL - 4 pixels
Minimum 5 Pixels
Figure 22. Line Rate Timing with OneShot=1 & VSreject=1
SETTING POWER AND PERFORMANCE WITH Rext
The power and performance levels of the XRD98L61
are set by the value of Rext. Rext sets the current bias
level for the entire chip. Rext is connected between pin
39 (ExtRef) and analog ground (see Figure 23). This
resistor should be placed as close as possible to the
pin and routed directly to a ground plane in a PCB
layout.
A surface mount carbon resistor is recom-
mended.
Increasing values of Rext decrease the power, linearity
and noise performance of the XRD98L61. Lowering the
value of Rext increases linearity and noise perfor-
mance while increasing power.
The tested default
value for Rext is 30KOhms.
In order to match system to system performance and
set consistent manufacturable performance levels
between cameras, it is recommended that the Rext
resistor have <1% tolerance.
Digital-to-Analog Converters
There are two voltage output, 8-bit resolution, Digital-
to-Analog Converters (DACs) which can be used for a
variety of purposes, and are controlled via the serial
interface. On power up, these DACs are disabled. To
activate them, you must write a "0" to the DAC0pd and
DAC1pd bits in the Control register.
相關PDF資料 |
PDF描述 |
|---|---|
| LGU2G391MELB | CAP ALUM 390UF 400V 20% SNAP |
| ECC31DCMT | CONN EDGECARD 62POS .100 WW |
| 1589448-3 | STRIP CON |
| AD8335-EVALZ | BOARD EVALUATION FOR AD8335 |
| RSM06DRSI-S288 | CONN EDGECARD 12POS DIP .156 SLD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRD98L62 | 制造商:EXAR 制造商全稱:EXAR 功能描述:CCD Image Digitizers with CDS, PGA and 12-Bit A/D |
| XRD98L62ACV | 制造商:EXAR 制造商全稱:EXAR 功能描述:CCD Image Digitizers with CDS, PGA and 12-Bit A/D |
| XRD98L62ACV-F | 功能描述:視頻 IC RoHS:否 制造商:Fairchild Semiconductor 工作電源電壓:5 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-28 封裝:Reel |
| XRD98L62EVAL | 功能描述:數據轉換 IC 開發工具 XRD98L62 EVAL BOARD RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| XRD98L62ZEVAL | 功能描述:數據轉換 IC 開發工具 Eval Board (Solder) XRD98L62AIV RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
發布緊急采購，3分鐘左右您將得到回復。