參數資料
型號: XR20M1172G28-0A-EB
廠商: Exar Corporation
文件頁數: 33/55頁
文件大?。?/td> 0K
描述: EVAL BOARD FOR XR20M1172 28TSSOP
標準包裝: 1
主要目的: 接口,UART
嵌入式:
已用 IC / 零件: XR20M1172
主要屬性: 2 通道
次要屬性: I²C & SPI 接口
已供物品:
其它名稱: 1016-1622
XR20M1172G28-0A-EB-ND
XR20M1172
39
REV. 1.2.0
TWO CHANNEL I2C/SPI UART WITH 64-BYTE FIFO
4.19
Extra Features Control Register (EFCR) - Read/Write
EFCR[7]: IrDA mode
This bit selects between the slow and fast IrDA modes. See “Section 2.15, Infrared Mode” on page 22 for
complete details.
Logic 0 = IrDA version 1.0, 3/16 pulse ratio, data rate up to 115.2 Kbps
Logic 1 = IrDA version 1.1, 1/4 pulse ratio, data rate up to 1.152 Mbps
EFCR[6]: Reserved
EFCR[5]: Auto RS-485 Polarity Inversion
This bit changes the polarity of the Auto RS-485 Half-Duplex Direction Control output (RTS#). This bit will only
affect the behavior of the RTS# output if EFCR[4] = 1. See “Section 2.14, Auto RS485 Half-duplex Control”
on page 20 for complete details.
Logic 0 = RTS# output is LOW when transmitting and HIGH when receiving.
Logic 1 = RTS# output is HIGH when transmitting and LOW when receiving.
EFCR[4]: Auto RS-485 Enable
This bit enables the RTS# output as the Auto RS-485 Half-Duplex Direction Control output. See “Section
2.14, Auto RS485 Half-duplex Control” on page 20 for complete details.
Logic 0 = RTS# output can be used for Auto RTS Hardware Flow Control or as a general purpose output.
Logic 1 = RTS# output enabled as the Auto RS-485 Half-Duplex Direction Control output.
EFCR[3]: Reserved
EFCR[2]: Transmitter Disable
UART does not send serial data out on the TX output pin, but the TX FIFO will continue to receive data from
CPU until full. Any data in the TSR will be sent out before the trasnmitter goes into disable state.
Logic 0 = Transmitter is enabled
Logic 1 = Transmitter is disabled
EFCR[1] = Receiver Disable
UART will stop receiving data immediately once this bit is set to a Logic 1. Any data that is being received in
the TSR will be received correctly and sent to the RX FIFO.
Logic 0 = Receiver is enabled
Logic 1 = Receiver is disabled
EFCR[0]: 9-bit or Multidrop Mode Enable
This bit enables 9-bit or Multidrop mode. See “Section 2.14, Auto RS485 Half-duplex Control” on page 20
for complete details.
Logic 0 = Normal 8-bit mode
Logic 1 = Enable 9-bit or Multidrop mode
4.20
Baud Rate Generator Registers (DLL, DLM and DLD[3:0]) - Read/Write
These registers make-up the value of the baud rate divisor. The concatenation of the contents of DLM and
DLL is a 16-bit value is then added to DLD[3:0]/16 to achieve the fractional baud rate divisor. DLD must be
enabled via EFR bit-4 before it can be accessed. SEE”PROGRAMMABLE BAUD RATE GENERATOR WITH
FRACTIONAL DIVISOR” ON PAGE 13.
相關PDF資料
PDF描述
MLF2012E5R6J INDUCTOR MULTILAYER 5.6UH 0805
XR20M1170L24-0B-EB EVAL BOARD FOR XR20M1170 24QFN
RPP30-4824S CONV DC/DC 30W 36-75VIN 24VOUT
RPP30-2424S-F CONV DC/DC 30W 18-36VIN 24VOUT
MLF2012A4R7J INDUCTOR MULTILAYER 4.7UH 0805
相關代理商/技術參數
參數描述
XR20M1172G28-0B-EB 功能描述:界面開發工具 Supports M1172 28 ld TSSOP, SPI Interface RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
XR20M1172IG28 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR20M1172IG28-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR20M1172IG28-F 制造商:Exar Corporation 功能描述:IC DUAL UART 16MBPS 3.63V 28-TSSOP 制造商:Exar Corporation 功能描述:IC, DUAL UART, 16MBPS, 3.63V, 28-TSSOP
XR20M1172IG28TR-F 功能描述:UART 接口集成電路 1.8V 2 Ch 64-byte I2C/SPI UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel