- 您現在的位置：買賣IC網 > PDF目錄16841 > XR20M1172G28-0A-EB (Exar Corporation)EVAL BOARD FOR XR20M1172 28TSSOP PDF資料下載
參數資料
| 型號： | XR20M1172G28-0A-EB |
| 廠商： | Exar Corporation |
| 文件頁數： | 32/55頁 |
| 文件大小： | 0K |
| 描述： | EVAL BOARD FOR XR20M1172 28TSSOP |
| 標準包裝： | 1 |
| 主要目的： | 接口，UART |
| 嵌入式： | 否 |
| 已用 IC / 零件： | XR20M1172 |
| 主要屬性： | 2 通道 |
| 次要屬性： | I²C & SPI 接口 |
| 已供物品： | 板 |
| 其它名稱： | 1016-1622 XR20M1172G28-0A-EB-ND |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁
XR20M1172
38
TWO CHANNEL I2C/SPI UART WITH 64-BYTE FIFO
REV. 1.2.0
4.15
GPIO Direction Register (IODir) - Read/Write
This register is used to program the direction of the GPIO pins. Bit-7 to bit-0 controls GPIO7 to GPIO0.
Logic 0 = set GPIO pin as input
Logic 1 = set GPIO pin as output
4.16
GPIO State Register (IOState) = Read/Write
This register reports the state of all GPIO pins during a read and writes to any GPIO that is an output.
Logic 0 = set output pin LOW
Logic 1 = set output pin HIGH
4.17
GPIO Interrupt Enable Register (IOIntEna) - Read/Write
This register enables the interrupt for the GPIO pins. The interrupts for GPIO[7:4] are only enabled if
IOControl[1] = 0. If IOControl[0] = 1 (GPIO pins are selected as modem IOs) , then IOIntEna[7:4] will have no
effect on GPIO[7:4].
Logic 0 = a change in the input pin will not generate an interrupt
Logic 1 = a change in the input will generate an interrupt
4.18
GPIO Control Register (IOControl) - Read/Write
IOControl[7:4]: Reserved
IOControl[3]: UART Software Reset
Writing a logic 1 to this bit will reset the device. Once the device is reset, this bit will automatically be set to a
logic 0.
IOControl[2]: GPIO[3:0] or Modem IO Select (CH B)
This bit controls whether GPIO[3:0] behave as GPIO pins or as modem IO pins (RIB#, CDB#, DTRB#, DSRB#)
Logic 0 = GPIO[3:0] behave as GPIO pins
Logic 1 = GPIO[3:0] behave as RIB#, CDB#, DTRB#, DSRB#. Note: DTRB# will also need to be set as an
output via IODir bit-1.
IOControl[1]: GPIO[7:4] or Modem IO Select (CH A)
This bit controls whether GPIO[7:4] behave as GPIO pins or as modem IO pins (RIA#, CDA#, DTRA#, DSRA#)
Logic 0 = GPIO[7:4] behave as GPIO pins
Logic 1 = GPIO[7:4] behave as RIA#, CDA#, DTRA#, DSRA#. Note: DTRA# will also need to be set as an
output via IODir bit-5.
IOControl[0]: IO Latch
This bit enable/disable GPIO inputs latching.
Logic 0 = GPIO input values are not latched. A change in any GPIO input generates an interrupt. A read of
the IOState register clears the interrupt. If the input goes back to its initial logic state before the input register
is read, then the interrupt is cleared.
Logic 1 = GPIO input values are latched. A change in the GPIO input generates an interrupt and the input
logic value is loaded in the bit of the corresponding input state register (IOState). A read of the IOState
register clears the interrupt. If the input pin goes back to its initial logic state before the interrupt register is
read, then the interrupt is not cleared and the corresponding bit of the IOState register keeps the logic value
that generated the interrupt.
相關PDF資料 |
PDF描述 |
|---|---|
| MLF2012E5R6J | INDUCTOR MULTILAYER 5.6UH 0805 |
| XR20M1170L24-0B-EB | EVAL BOARD FOR XR20M1170 24QFN |
| RPP30-4824S | CONV DC/DC 30W 36-75VIN 24VOUT |
| RPP30-2424S-F | CONV DC/DC 30W 18-36VIN 24VOUT |
| MLF2012A4R7J | INDUCTOR MULTILAYER 4.7UH 0805 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR20M1172G28-0B-EB | 功能描述:界面開發工具 Supports M1172 28 ld TSSOP, SPI Interface RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XR20M1172IG28 | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR20M1172IG28-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR20M1172IG28-F | 制造商:Exar Corporation 功能描述:IC DUAL UART 16MBPS 3.63V 28-TSSOP 制造商:Exar Corporation 功能描述:IC, DUAL UART, 16MBPS, 3.63V, 28-TSSOP |
| XR20M1172IG28TR-F | 功能描述:UART 接口集成電路 1.8V 2 Ch 64-byte I2C/SPI UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。