REV. 1.1.0 2.0 FUNCTIONAL DESCRIPTIONS 2.1 CPU Interface The M1170 ca" />
參數資料
型號: XR20M1170L28-0B-EB
廠商: Exar Corporation
文件頁數: 53/56頁
文件大?。?/td> 0K
描述: EVAL BOARD FOR XR20M1170 28QFN
標準包裝: 1
主要目的: 接口,UART
嵌入式:
已用 IC / 零件: XR20M1170
次要屬性: I²C & SPI 接口
已供物品:
XR20M1170
6
I2C/SPI UART WITH 64-BYTE FIFO
REV. 1.1.0
2.0 FUNCTIONAL DESCRIPTIONS
2.1
CPU Interface
The M1170 can operate with either an I2C-bus interface or an SPI interface. The CPU interface is selected via
the I2C/SPI# input pin.
2.1.1
I2C-bus Interface
The I2C-bus interface is compliant with the Standard-mode and Fast-mode I2C-bus specifications. The I2C-
bus interface consists of two lines: serial data (SDA) and serial clock (SCL). In the Standard-mode, the serial
clock and serial data can go up to 100 kbps and in the Fast-mode, the serial clock and serial data can go up to
400 kbps. The first byte sent by an I2C-bus master contains a start bit (SDA transition from HIGH to LOW
when SCL is HIGH), 7-bit slave address and whether it is a read or write transaction. The next byte is the sub-
address that contains the address of the register to access. The M1170 responds to each write with an
acknowledge (SDA driven LOW by M1170 for one clock cycle when SCL is HIGH). If the TX FIFO is full, the
M1170 will respond with a negative acknowledge (SDA driven HIGH by M1170 for one clock cycle when SCL is
HIGH) when the CPU tries to write to the TX FIFO. The last byte sent by an I2C-bus master contains a stop bit
(SDA transition from LOW to HIGH when SCL is HIGH). See Figures 3 - 5 below. For complete details, see
the I2C-bus specifications.
FIGURE 3. I C START AND STOP CONDITIONS
SDA
SCL
S
P
START condition
STOP condition
FIGURE 4. MASTER WRITES TO SLAVE (M1170)
SW
A
AP
SLAVE
ADDRESS
REGISTER
ADDRESS
nDATA
White block: host to UART
Grey block: UART to host
FIGURE 5. MASTER READS FROM SLAVE (M1170)
SW
A
AR
SLAVE
ADDRESS
REGISTER
ADDRESS
White block: host to UART
Grey block: UART to host
A
S
SLAVE
ADDRESS
nDATA
ANA
P
LAST DATA
2
相關PDF資料
PDF描述
XR20M1170L28-0A-EB EVAL BOARD FOR XR20M1170 28QFN
EBA31DRMS CONN EDGECARD 62POS .125 SQ WW
SLPX682M050C7P3 CAP ALUM 6800UF 50V 20% SNAP
HBC10DRTN-S93 CONN EDGECARD 20POS DIP .100 SLD
6A44-B0441-050.0-0 CABLE CX4-CX4 DDR 4CH LSZH 50M
相關代理商/技術參數
參數描述
XR20M1172 制造商:EXAR 制造商全稱:EXAR 功能描述:TWO CHANNEL I2C/SPI UART WITH 64-BYTE FIFO
XR20M1172_09 制造商:EXAR 制造商全稱:EXAR 功能描述:TWO CHANNEL I2C/SPI UART WITH 64-BYTE FIFO
XR20M1172G28-0A-EB 功能描述:UART 接口集成電路 Supports M1172 28 ld TSSOP, I2C Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR20M1172G28-0B-EB 功能描述:界面開發工具 Supports M1172 28 ld TSSOP, SPI Interface RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
XR20M1172IG28 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel