REV. 1.1.0 I2C/SPI UART WITH 64-BYTE FIFO FCR[1]: RX FIFO Reset This bit is only active when FCR bit-0 is a ‘1’ and requires at le" />
參數資料
型號： XR20M1170L28-0B-EB
廠商： Exar Corporation
文件頁數： 22/56頁
文件大?。?/td> 0K
描述： EVAL BOARD FOR XR20M1170 28QFN
標準包裝： 1
主要目的： 接口，UART
嵌入式： 否
已用 IC / 零件： XR20M1170
次要屬性： I²C & SPI 接口
已供物品： 板
XR20M1170
29
REV. 1.1.0
I2C/SPI UART WITH 64-BYTE FIFO
FCR[1]: RX FIFO Reset
This bit is only active when FCR bit-0 is a ‘1’ and requires at least 3 XTAL clocks to reset.
Logic 0 = No receive FIFO reset (default)
Logic 1 = Reset the receive FIFO pointers and FIFO level counter logic (the receive shift register is not
cleared or altered). This bit will return to a logic 0 after resetting the FIFO.
FCR[2]: TX FIFO Reset
This bit is only active when FCR bit-0 is a ‘1’ and requires at least 3 XTAL clocks to reset.
Logic 0 = No transmit FIFO reset (default).
Logic 1 = Reset the transmit FIFO pointers and FIFO level counter logic (the transmit shift register is not
cleared or altered). This bit will return to a logic 0 after resetting the FIFO.
FCR[3]: Reserved
This is a legacy register bit that does not have any functionality in the XR20M1170.
FCR[5:4]: Transmit FIFO Trigger Select (requires EFR bit-4=1)
(logic 0 = default, TX trigger level = 1)
These 2 bits set the trigger level for the transmit FIFO. The UART will issue a transmit interrupt when the
number of spaces in the FIFO is above the selected trigger level, or when it gets empty in case that the FIFO
did not get filled over the trigger level on last re-load. Table 10 shows the selections. The UART will issue a
transmit interrupt when the number of available spaces in the FIFO is less than the transmit trigger level.
Table 10 shows the selections.
FCR[7:6]: Receive FIFO Trigger Select
(logic 0 = default, RX trigger level =1)
These 2 bits are used to set the trigger level for the receive FIFO. The UART will issue a receive interrupt when
the number of the characters in the FIFO is greater than the receive trigger level or when a receive data
TABLE 10: TRANSMIT AND RECEIVE FIFO TRIGGER LEVEL SELECTION
BIT-7
BIT-6
BIT-5
BIT
-4
RECEIVE
TRIGGER LEVEL
(CHARACTERS)
TRANSMIT
TRIGGER LEVEL
(SPACES)
0
1
0
1
0
1
0
1
0
1
0
1
8
16
56
60
8
16
32
56
FCR
相關PDF資料
PDF描述
XR20M1170L28-0A-EB EVAL BOARD FOR XR20M1170 28QFN
EBA31DRMS CONN EDGECARD 62POS .125 SQ WW
SLPX682M050C7P3 CAP ALUM 6800UF 50V 20% SNAP
HBC10DRTN-S93 CONN EDGECARD 20POS DIP .100 SLD
6A44-B0441-050.0-0 CABLE CX4-CX4 DDR 4CH LSZH 50M
相關代理商/技術參數
參數描述
XR20M1172 制造商:EXAR 制造商全稱:EXAR 功能描述:TWO CHANNEL I2C/SPI UART WITH 64-BYTE FIFO
XR20M1172_09 制造商:EXAR 制造商全稱:EXAR 功能描述:TWO CHANNEL I2C/SPI UART WITH 64-BYTE FIFO
XR20M1172G28-0A-EB 功能描述:UART 接口集成電路 Supports M1172 28 ld TSSOP, I2C Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR20M1172G28-0B-EB 功能描述:界面開發工具 Supports M1172 28 ld TSSOP, SPI Interface RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
XR20M1172IG28 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*