- 您現在的位置：買賣IC網 > PDF目錄16827 > XR17V354IB-0A-EVB (Exar Corporation)EVAL BOARD FOR XR17V354-A 176BGA PDF資料下載
參數資料
| 型號： | XR17V354IB-0A-EVB |
| 廠商： | Exar Corporation |
| 文件頁數： | 49/66頁 |
| 文件大小： | 0K |
| 描述： | EVAL BOARD FOR XR17V354-A 176BGA |
| 產品培訓模塊： | PCIe UARTs |
| 標準包裝： | 1 |
| 主要目的： | 接口，UART |
| 嵌入式： | 否 |
| 已用 IC / 零件： | XR17V354 |
| 已供物品： | 板 |
| 其它名稱： | 1016-1611 XR17V354IB-0A-EVB-ND |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁當前第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁
XR17V354
53
REV. 1.0.3
HIGH PERFORMANCE QUAD PCI-EXPRESS UART
MCR[7]: Clock Prescaler Select (requires EFR bit [4]=1)
Logic 0 = Divide by one. The internal 125MHz clock (master) or 62.5MHz clock (slave) is fed directly to the
Programmable Baud Rate Generator without further modification, i.e., divide by one (default).
Logic 1 = Divide by four. The prescaler divides the internal 125MHz clock (master) or 62.5MHz clock (slave)
by 4 and feeds it to the Programmable Baud Rate Generator, hence, data rates become one forth.
MCR[6]: Infrared Encoder/Decoder Enable (requires EFR bit [4]=1)
The state of this bit depends on the sampled logic level of pin ENIR during power up, following a hardware
reset (rising edge of RST# input). Afterward user can override this bit for desired operation.
Logic 0 = Enable the standard modem receive and transmit character interface.
Logic 1 = Enable infrared IrDA receive and transmit inputs/outputs. While in this mode, the TX/RX output/
input are routed to the infrared encoder/decoder. The data input and output levels will conform to the IrDA
infrared interface requirement. As such, while in this mode the infrared TX output will be a LOW during idle
data conditions. FCTR bit [4] may be selected to invert the RX input signal level going to the decoder for
infrared modules that provide rather an inverted output. For exact 3/16 or 1/4 bit wide pulse, the 16X
sampling rate must be used and DLD[3:0] = ’0000’. If DLD[3:0] is not ’0000’, the pulse width can vary.
MCR[5]: Xon-Any Enable (requires EFR bit [4]=1)
Logic 0 = Disable Xon-Any function (default).
Logic 1 = Enable Xon-Any function. In this mode any RX character received will enable Xon, resume data
transmission.
MCR[4]: Internal Loopback Enable
Logic 1 = Disable loopback mode (default).
Logic 1 = Enable local loopback mode, see loopback section and Figure 12.
MCR[3]: Send Char Immediate (OP2 in Local Loopback Mode)
This bit is used to transmit a character immediately irrespective of the bytes currently in the transmit FIFO. The
data byte must be loaded into the transmit holding register (THR) immediately following the write to this bit (to
set it to a ’1’). In other words, no other register must be accessed between setting this bit and writing to the
THR. The loaded byte will be transmitted ahead of all the bytes in the TX FIFO, immediately after the character
currently being shifted out of the transmit shift register is sent out. The existing line parameters (parity, stop
bits) will be used when composing the character. This bit is self clearing, therefore, must be set before sending
a custom character each time. Please note that the Transmitter must be enabled for this function (MSR[3] = 0).
Also, if software flow control is enabled, the software flow control characters (Xon, Xoff) have higher priority
and will get shifted out before the custom byte is transmitted.
Logic 0 = Send Char Immediate disabled (default).
Logic 1 = Send Char Immediate enabled.
In Local Loopback Mode (MCR[4] = 1), this bit acts as the legacy OP2 output and controls the CD bit in the
MSR register as shown in Figure 12. Please make sure that this bit is a ’0’ when exiting the Local Loopback
Mode.
相關PDF資料 |
PDF描述 |
|---|---|
| 202A196-3-0 | BOOT MOLDED |
| 570-002-734-100 | ASSEMBLY PLUG 2POS WATERPROOF |
| LMR040-0700-CCF9-2KIT4X | KIT DEV LMR040-0700, 230V |
| 322A024-25-0 | BOOT MOLDED |
| 0210490393 | CABLE JUMPER 1.25MM .102M 32POS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR17V354IB176-F | 功能描述:UART 接口集成電路 4 Channel PCIe UART w/256 Byte FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR17V354IB-E4-EVB | 功能描述:界面開發(fā)工具 Eval Board for XR17V354IB-E4 RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XR17V354IB-E8-EVB | 功能描述:界面開發(fā)工具 Eval Board for XR17V354IB-E8 RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XR17V358 | 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE OCTAL PCI EXPRESS UART |
| XR17V358IB-0A-EVB | 功能描述:界面開發(fā)工具 Eval Board for XR17V358IB-0A RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
發(fā)布緊急采購，3分鐘左右您將得到回復。