- 您現在的位置：買賣IC網 > PDF目錄16827 > XR17V354IB-0A-EVB (Exar Corporation)EVAL BOARD FOR XR17V354-A 176BGA PDF資料下載
參數資料
| 型號： | XR17V354IB-0A-EVB |
| 廠商： | Exar Corporation |
| 文件頁數： | 42/66頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVAL BOARD FOR XR17V354-A 176BGA |
| 產品培訓模塊： | PCIe UARTs |
| 標準包裝： | 1 |
| 主要目的： | 接口，UART |
| 嵌入式： | 否 |
| 已用 IC / 零件： | XR17V354 |
| 已供物品： | 板 |
| 其它名稱： | 1016-1611 XR17V354IB-0A-EVB-ND |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁當前第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁
XR17V354
47
REV. 1.0.3
HIGH PERFORMANCE QUAD PCI-EXPRESS UART
4.4.2
IER versus Receive/Transmit FIFO Polled Mode Operation
When FCR bit [0] equals a logic 1 for FIFO enable; resetting IER bits [3:0] enables the XR16V354 in the FIFO
polled mode of operation. Since the receiver and transmitter have separate bits in the LSR either can be used
in the polled mode by selecting respective transmit or receive control bit(s).
A. LSR BIT-0 indicates there is data in RHR (non-FIFO mode) or RX FIFO (FIFO mode).
B. LSR BIT-1 indicates an overrun error has occurred and that data in the FIFO may not be valid.
C. LSR BIT 2-4 provides the type of receive data errors encountered for the data byte in RHR, if any.
D. LSR BIT-5 indicates THR (non-FIFO mode) or TX FIFO (FIFO mode) is empty.
E. LSR BIT-6 indicates when both the transmit FIFO and TSR are empty.
F. LSR BIT-7 indicates a data error in at least one character in the RX FIFO.
IER[7]: CTS# Input Interrupt Enable (requires EFR bit [4]=1)
Logic 0 = Disable the CTS# interrupt (default).
Logic 1 = Enable the CTS# interrupt. The UART issues an interrupt when CTS# pin makes a transition from
LOW to HIGH.
IER[6]: RTS# Output Interrupt Enable (requires EFR bit [4]=1)
Logic 0 = Disable the RTS# interrupt (default).
Logic 1 = Enable the RTS# interrupt. The UART issues an interrupt when RTS# pin makes a transition from
LOW to HIGH.
IER[5]: Xoff Interrupt Enable (requires EFR bit [4]=1)
Logic 0 = Disable the software flow control, receive Xoff interrupt (default).
Logic 1 = Enable the software flow control, receive Xoff interrupt. See Software Flow Control section for
details.
IER[4]: Reserved
IER[3]: Modem Status Interrupt Enable
The Modem Status Register interrupt is issued whenever any of the delta bits of the MSR register (bits [3:0]) is
set.
Logic 0 = Disable the modem status register interrupt (default).
Logic 1 = Enable the modem status register interrupt.
IER[2]: Receive Line Status Interrupt Enable
An Overrun error, Framing error, Parity error or detection of a Break character will result in an LSR interrupt.
The V354 will issue an LSR interrupt immediately after receiving a character with an error. It will again re-issue
the interrupt (if the first one has been cleared by reading the LSR register) when the character with the error is
on the top of the FIFO, meaning the next one to be read out of the FIFO.
For example, let’s consider an incoming data stream of 0x55, 0xAA, etc. and that the character 0xAA has a
Parity error associated with it. Let’s assume that the character 0x55 has not been read out of the FIFO yet. The
V354v354 will issue an interrupt as soon as the stop bit of the character 0xAA is received. The LSR register will
have only the FIFO error bit (bit [7]) set and none of the other error bits (bits [4:1]) will be set, since the byte on
the top of the FIFO is 0x55 which does not have any errors associated with it. When this byte has been read
out, the V354 will issue another LSR interrupt and this time the LSR register will show the Parity bit (bit [2]) set.
Logic 0 = Disable the receiver line status interrupt (default).
Logic 1 = Enable the receiver line status interrupt.
相關PDF資料 |
PDF描述 |
|---|---|
| 202A196-3-0 | BOOT MOLDED |
| 570-002-734-100 | ASSEMBLY PLUG 2POS WATERPROOF |
| LMR040-0700-CCF9-2KIT4X | KIT DEV LMR040-0700, 230V |
| 322A024-25-0 | BOOT MOLDED |
| 0210490393 | CABLE JUMPER 1.25MM .102M 32POS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR17V354IB176-F | 功能描述:UART 接口集成電路 4 Channel PCIe UART w/256 Byte FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR17V354IB-E4-EVB | 功能描述:界面開發工具 Eval Board for XR17V354IB-E4 RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XR17V354IB-E8-EVB | 功能描述:界面開發工具 Eval Board for XR17V354IB-E8 RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XR17V358 | 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE OCTAL PCI EXPRESS UART |
| XR17V358IB-0A-EVB | 功能描述:界面開發工具 Eval Board for XR17V358IB-0A RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
發布緊急采購，3分鐘左右您將得到回復。