- 您現在的位置：買賣IC網 > PDF目錄376455 > XR17D158IV (EXAR CORP) UNIVERSAL (3.3V AND 5V) PCI BUS OCTAL UART PDF資料下載
參數資料
| 型號： | XR17D158IV |
| 廠商： | EXAR CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | UNIVERSAL (3.3V AND 5V) PCI BUS OCTAL UART |
| 中文描述： | 8 CHANNEL(S), 6.25M bps, SERIAL COMM CONTROLLER, PQFP144 |
| 封裝： | 20 X 20 MM, 1.40 MM HEIGHT, TQFP-144 |
| 文件頁數： | 46/72頁 |
| 文件大?。?/td> | 1520K |
| 代理商： | XR17D158IV |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁當前第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁
XR17D158
UNIVERSAL (3.3V AND 5V) PCI BUS OCTAL UART
xr
REV. 1.2.1
46
LCR[6]: Transmit Break Enable
When enabled the Break control bit causes a break condition to be transmitted (the TX output is forced to a
“space", LOW state). This condition remains until disabled by setting LCR bit-6 to a logic 0.
Logic 0 = No TX break condition (default).
Logic 1 = Forces the transmitter output (TX) to a “space”, LOW, for alerting the remote receiver of a line
break condition.
LCR[7]: Baud Rate Divisors Enable
Baud rate generator divisor (DLL/DLM) enable.
Logic 0 = Data registers are selected (default).
Logic 1 = Divisor latch registers are selected.
5.8.8
The MCR register is used for controlling the modem interface signals or general purpose inputs/outputs.
MCR[0]: DTR# Pins
The DTR# pin may be used for automatic hardware flow control enabled by EFR bit-6 and MCR bit-2=1. If the
modem interface is not used, this output may be used for general purpose.
Logic 0 = Force DTR# output HIGH (default).
Logic 1 = Force DTR# output LOW.
Modem Control Register (MCR) - Read/Write
MCR[1]: RTS# Pins
The RTS# pin may be used for automatic hardware flow control by enabled by EFR bit-6 and MCR bit-2=0. If
the modem interface is not used, this output may be used for general purpose.
Logic 0 = Force RTS# output HIGH (default).
Logic 1 = Force RTS# output LOW.
MCR[2]: DTR# or RTS# for Auto Flow Control
DTR# or RTS# auto hardware flow control select. This bit is in effect only when auto RTS/DTR is enabled by
EFR bit-6. DTR# selection is associated with DSR# and RTS# is with CTS#.
Logic 0 = Uses RTS# and CTS# pins for auto hardware flow control.
Logic 1 = Uses DTR# and DSR# pins for auto hardware flow control.
MCR[3]: (OP2)
The OP2 output is not available in the XR17D158. It is present for 16C550 compatibility during internal
loopback. See
Figure 18
. Logic 0 is default.
MCR[4]: Internal Loopback Enable
Logic 0 = Disable internal loopback mode (default).
Logic 1 = Enable internal loopback mode, see loopback section and
Figure 18
.
T
ABLE
16: P
ARITY
SELECTION
LCR B
IT
-5 LCR B
IT
-4 LCR B
IT
-3
P
ARITY
SELECTION
X
X
0
No parity
0
0
1
Odd parity
0
1
1
Even parity
1
0
1
Force parity to mark, “1”
1
1
1
Forced parity to space, “0”
相關PDF資料 |
PDF描述 |
|---|---|
| XR17D158 | UNIVERSAL (3.3V AND 5V) PCI BUS OCTAL UART |
| XR17D158CV | UNIVERSAL (3.3V AND 5V) PCI BUS OCTAL UART |
| XR17L152IM | CAP .068UF 400V PEN FILM 2825 5% |
| XR17L152 | 3.3V PCI BUS DUAL UART |
| XR17L152CM | 3.3V PCI BUS DUAL UART |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR17D158IV-F | 功能描述:UART 接口集成電路 3.3V-5V 64B FIFO temp -45 to 85C;UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR17D158IVTR-F | 制造商:Exar Corporation 功能描述:UART 8-CH 64Byte FIFO 5V 144-Pin LQFP T/R 制造商:Exar Corporation 功能描述:XR17D158IVTR-F |
| XR17L152 | 制造商:EXAR 制造商全稱:EXAR 功能描述:3.3V PCI BUS DUAL UART |
| XR17L152CM | 制造商:EXAR 制造商全稱:EXAR 功能描述:3.3V PCI BUS DUAL UART |
| XR17L152IM | 制造商:EXAR 制造商全稱:EXAR 功能描述:3.3V PCI BUS DUAL UART |
發布緊急采購，3分鐘左右您將得到回復。