REV. 1.0.2 HIGH PERFORMANCE DUART WITH 32-BYTE FIFO AND POWERSAVE FEATURE PIN DESCRIPTIONS Pin Description N
參數資料
型號： XR16V2651IM-0B-EB
廠商： Exar Corporation
文件頁數： 23/51頁
文件大?。?/td> 0K
描述： EVAL BOARD FOR V2651 48TQFP
標準包裝： 1
系列： *
XR16V2651
3
REV. 1.0.2
HIGH PERFORMANCE DUART WITH 32-BYTE FIFO AND POWERSAVE FEATURE
PIN DESCRIPTIONS
Pin Description
NAME
32-QFN
PIN #
48-TQFP
PIN #
TYPE
DESCRIPTION
DATA BUS INTERFACE
A2
A1
A0
18
19
20
26
27
28
I
Address data lines [2:0]. These 3 address lines select one of the internal registers
in UART channel A/B during a data bus transaction.
D7
D6
D5
D4
D3
D2
D1
D0
2
1
32
31
30
29
28
27
3
2
1
48
47
46
45
44
I/O Data bus lines [7:0] (bidirectional).
IOR#
(VCC)
14
19
I
When 16/68# pin is HIGH, the Intel bus interface is selected and this input
becomes read strobe (active low). The falling edge instigates an internal read cycle
and retrieves the data byte from an internal register pointed by the address lines
[A2:A0], puts the data byte on the data bus to allow the host processor to read it on
the rising edge.
When 16/68# pin is LOW, the Motorola bus interface is selected and this input is
not used and should be connected to VCC.
IOW#
(R/W#)
12
15
I
When 16/68# pin is HIGH, it selects Intel bus interface and this input becomes write
strobe (active low). The falling edge instigates the internal write cycle and the rising
edge transfers the data byte on the data bus to an internal register pointed by the
address lines.
When 16/68# pin is LOW, the Motorola bus interface is selected and this input
becomes read (HIGH) and write (LOW) signal.
CSA#
(CS#)
7
10
I
When 16/68# pin is HIGH, this input is chip select A (active low) to enable channel
A in the device.
When 16/68# pin is LOW, this input becomes the chip select (active low) for the
Motorola bus interface.
CSB#
(A3)
8
11
I
When 16/68# pin is HIGH, this input is chip select B (active low) to enable channel
B in the device.
When 16/68# pin is LOW, this input becomes address line A3 which is used for
channel selection in the Motorola bus interface. Input logic 0 selects channel A and
logic 1 selects channel B.
INTA
(IRQ#)
22
30
O
When 16/68# pin is HIGH for Intel bus interface, this output becomes channel A
interrupt output. The output state is defined by the user through the software set-
ting of MCR[3]. INTA is set to the active mode and OP2A# output to a logic 0 when
MCR[3] is set to a logic 1. INTA is set to the three state mode and OP2A# to a logic
1 when MCR[3] is set to a logic 0. See MCR[3].
When 16/68# pin is LOW for Motorola bus interface, this output becomes device
interrupt output (active low, open drain). An external pull-up resistor is required for
proper operation.
相關PDF資料
PDF描述
VE-JVN-EZ-S CONVERTER MOD DC/DC 18.5V 25W
EEM28DTMN-S189 CONN EDGECARD 56POS R/A .156 SLD
GSM11DRTH-S13 CONN EDGECARD 22POS .156 EXTEND
A3DDH-1636G IDC CABLE - AKR16H/AE16G/AKR16H
VE-JVK-EZ-S CONVERTER MOD DC/DC 40V 25W
相關代理商/技術參數
參數描述
XR16V2651IM-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16V2651IMTR-F 制造商:Exar Corporation 功能描述:UART 2-CH 32Byte FIFO 2.5V/3.3V 48-Pin TQFP T/R 制造商:Exar Corporation 功能描述:XR16V2651IMTR-F
XR16V2652 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE DUART WITH 32-BYTE FIFO
XR16V2652_07 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE DUART WITH 32-BYTE FIFO
XR16V2652IJ 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*