REV. 1.0.2 HIGH PERFORMANCE DUART WITH 32-BYTE FIFO 2.13 Auto RTS (Hardware) Flow Control Automatic RTS hardware flo" />
參數資料
型號： XR16V2650IL-0B-EB
廠商： Exar Corporation
文件頁數： 7/47頁
文件大小： 0K
描述： EVAL BOARD FOR V2650 32QFN
標準包裝： 1
系列： *
XR16V2650
15
REV. 1.0.2
HIGH PERFORMANCE DUART WITH 32-BYTE FIFO
2.13
Auto RTS (Hardware) Flow Control
Automatic RTS hardware flow control is used to prevent data overrun to the local receiver FIFO. The RTS#
output is used to request remote unit to suspend/resume data transmission. The auto RTS flow control
features is enabled to fit specific application requirement (see Figure 10):
Enable auto RTS flow control using EFR bit-6.
The auto RTS function must be started by asserting RTS# output pin (MCR bit-1 to logic 1 after it is enabled).
If using the Auto RTS interrupt:
Enable RTS interrupt through IER bit-6 (after setting EFR bit-4). The UART issues an interrupt when the
RTS# pin makes a transition from low to high: ISR bit-5 will be set to logic 1.
2.14
Auto RTS Hysteresis
The V2650 has a new feature that provides flow control trigger hysteresis while maintaining compatibility with
the XR16C850, ST16C650A and ST16C550 family of UARTs. With the Auto RTS function enabled, an interrupt
is generated when the receive FIFO reaches the selected RX trigger level. The RTS# pin will not be forced
HIGH (RTS off) until the receive FIFO reaches one trigger level above the selected trigger level in the trigger
table (Table 11). The RTS# pin will return LOW after the RX FIFO is unloaded to one level below the selected
trigger level. Under the above described conditions, the V2650 will continue to accept data until the receive
FIFO gets full. The Auto RTS function is initiated when the RTS# output pin is asserted LOW (RTS On).
2.15
Auto CTS Flow Control
Automatic CTS flow control is used to prevent data overrun to the remote receiver FIFO. The CTS# input is
monitored to suspend/restart the local transmitter. The auto CTS flow control feature is selected to fit specific
application requirement (see Figure 10):
Enable auto CTS flow control using EFR bit-7.
If using the Auto CTS interrupt:
Enable CTS interrupt through IER bit-7 (after setting EFR bit-4). The UART issues an interrupt when the
CTS# pin is de-asserted (HIGH): ISR bit-5 will be set to 1, and UART will suspend transmission as soon as
the stop bit of the character in process is shifted out. Transmission is resumed after the CTS# input is re-
asserted (LOW), indicating more data may be sent.
TABLE 6: AUTO RTS (HARDWARE) FLOW CONTROL
RX TRIGGER LEVEL
INT PIN ACTIVATION
RTS# DE-ASSERTED (HIGH)
(CHARACTERS IN RX FIFO)
RTS# ASSERTED (LOW)
(CHARACTERS IN RX FIFO)
8
16
0
16
24
8
24
28
16
28
24
相關PDF資料
PDF描述
EEM28DTMD-S189 CONN EDGECARD 56POS R/A .156 SLD
GMM11DRTH-S13 CONN EDGECARD 22POS .156 EXTEND
XR16V2651IL-0B-EB EVAL BOARD FOR V2651 32QFN
UPJ1C391MPD6TD CAP ALUM 390UF 16V 20% RADIAL
MCP1322T-46LE/OT IC SUPERVISOR 4.6V OD/PP SOT23-5
相關代理商/技術參數
參數描述
XR16V2650IL32 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE DUART WITH 32-BYTE FIFO
XR16V2650IL-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16V2650IM 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述:
XR16V2650IM-0B-EB 功能描述:UART 接口集成電路 Supports V2650 48 ld TQFP, PCI Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16V2650IM-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*