- 您現在的位置：買賣IC網 > PDF目錄3763 > XR16L2752IJ-F (Exar Corporation)IC UART FIFO 64B DUAL 44PLCC PDF資料下載
參數資料
| 型號： | XR16L2752IJ-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 34/49頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC UART FIFO 64B DUAL 44PLCC |
| 標準包裝： | 27 |
| 特點： | * |
| 通道數： | 2，DUART |
| FIFO's： | 64 字節 |
| 規程： | RS232，RS485 |
| 電源電壓： | 2.25 V ~ 5.5 V |
| 帶自動流量控制功能： | 是 |
| 帶IrDA 編碼器/解碼器： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 44-LCC（J 形引線） |
| 供應商設備封裝： | 44-PLCC（16.59x16.59） |
| 包裝： | 管件 |
| 其它名稱： | 1016-1650 XR16L2752IJ-F-ND |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁當前第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁
XR16L2752
xr
2.25V TO 5.5V DUART WITH 64-BYTE FIFO
REV. 1.2.1
4
RXA
39
I
UART channel A Receive Data or infrared receive data. Normal receive data input
must idle HIGH. The infrared receiver pulses typically idles LOW but can be inverted
by software control prior going in to the decoder, see MCR[6] and FCTR[2]. If this pin
is not used, tie it to VCC or pull it high via a 100k ohm resistor.
RTSA#
36
O
UART channel A Request-to-Send (active low) or general purpose output. This output
must be asserted prior to using auto RTS flow control, see EFR[6], MCR[1],
FCTR[1:0], EMSR[5:4] and IER[6]. For auto RS485 half-duplex direction control, see
FCTR[3] and EMSR[3].
CTSA#
40
I
UART channel A Clear-to-Send (active low) or general purpose input. It can be used
for auto CTS flow control, see EFR[7], and IER[7]. This input should be connected to
VCC when not used.
DTRA#
37
O
UART channel A Data-Terminal-Ready (active low) or general purpose output. If this
pin is not used, leave it unconnected.
DSRA#
41
I
UART channel A Data-Set-Ready (active low) or general purpose input. This input
should be connected to VCC when not used. This input has no effect on the UART.
CDA#
42
I
UART channel A Carrier-Detect (active low) or general purpose input. This input
should be connected to VCC when not used. This input has no effect on the UART.
RIA#
43
I
UART channel A Ring-Indicator (active low) or general purpose input. This input
should be connected to VCC when not used. This input has no effect on the UART.
MFA#
35
O
Multi-Function Output Channel A. This output pin can function as the OP2A#, BAUD-
OUTA#, or RXRDYA# pin. One of these output signal functions can be selected by
the user programmable bits 1-2 of the Alternate Function Register (AFR). These sig-
nal functions are described as follows:
1) OP2A# - When OP2A# (active low) is selected, the MF# pin is LOW when MCR bit-
3 is set to a logic 1 (see MCR bit-3). MCR bit-3 defaults to a logic 0 condition after a
reset or power-up.
2) BAUDOUTA# - When BAUDOUTA# function is selected, the 16X Baud rate clock
output is available at this pin.
3) RXRDYA# - RXRDYA# (active low) is intended for monitoring DMA data transfers.
See
Table 2 for more details.
TXB
26
O
UART channel B Transmit Data or infrared encoder data. Standard transmit and
receive interface is enabled when MCR[6] = 0. In this mode, the TX signal will be
HIGH during reset or idle (no data). Infrared IrDA transmit and receive interface is
enabled when MCR[6] = 1. In the Infrared mode, the inactive state (no data) for the
Infrared encoder/decoder interface is LOW. If it is not used, leave it unconnected.
RXB
25
I
UART channel B Receive Data or infrared receive data. Normal receive data input
must idle HIGH. The infrared receiver pulses typically idles LOW but can be inverted
by software control prior going in to the decoder, see MCR[6] and FCTR[2]. If this pin
is not used, tie it to VCC or pull it high via a 100k ohm resistor.
RTSB#
23
O
UART channel B Request-to-Send (active low) or general purpose output. This port
must be asserted prior to using auto RTS flow control, see EFR[6], MCR[1],
FCTR[1:0], EMSR[5:4] and IER[6]. For auto RS485 half-duplex direction control, see
FCTR[3] and EMSR[3].
Pin Description
NAME
44-PLCC
PIN #
TYPE
DESCRIPTION
相關PDF資料 |
PDF描述 |
|---|---|
| ST16C552IJ68-F | IC UART FIFO 16B DUAL 68PLCC |
| XR88C92IJ-F | IC UART FIFO DUAL 44PLCC |
| ST16C552ACJ68-F | IC UART FIFO 16B DUAL 68PLCC |
| ST16C650ACJ44-F | IC UART FIFO 32B 44PLCC |
| XR20M1170IG24-F | IC UART FIFO I2C/SPI 64B 24TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR16L2752IJTR-F | 制造商:Exar Corporation 功能描述:XR16L2752 Series 6.25 Mbps 5.5 V Dual UART With 64-Byte FIFO - PLCC-44 |
| XR16L570 | 制造商:EXAR 制造商全稱:EXAR 功能描述:SMALLEST 1.62V TO 5.5V UART WITH 16-BYTE FIFO AND POWERSAVE |
| XR16L570_07 | 制造商:EXAR 制造商全稱:EXAR 功能描述:SMALLEST 1.62V TO 5.5V UART WITH 16-BYTE FIFO AND POWERSAVE |
| XR16L570IL24 | 功能描述:UART 接口集成電路 UART w/ POWER SAVE RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16L570IL24-0B-EB | 功能描述:UART 接口集成電路 Supports L570 24 pin QFN, PCI Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。