- 您現在的位置：買賣IC網 > PDF目錄375045 > XQ2V3000 (Xilinx, Inc.) QPro Virtex-II 1.5V Military QML Platform FPGAs PDF資料下載
參數資料
| 型號： | XQ2V3000 |
| 廠商： | Xilinx, Inc. |
| 英文描述： | QPro Virtex-II 1.5V Military QML Platform FPGAs |
| 中文描述： | QPro的Virtex - II 1.5V的軍事QML第平臺FPGA |
| 文件頁數： | 11/128頁 |
| 文件大?。?/td> | 2738K |
| 代理商： | XQ2V3000 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁
QPro Virtex-II 1.5V Military QML Platform FPGAs
DS122 (v1.1) January 7, 2004
Product Specification
www.xilinx.com
1-800-255-7778
11
R
The optional weak-keeper circuit is connected to each out-
put. When selected, this circuit monitors the voltage on the
pad and weakly drives the pin High or Low. If the pin is con-
nected to a multiple-source signal, the weak-keeper holds
the signal in its last state if all drivers are disabled. Maintain-
ing a valid logic level in this way eliminates bus chatter.
Pull-up or pull-down resistors override the weak-keeper cir-
cuit.
LVTTL sinks and sources current up to 24 mA. The current
is programmable for LVTTL and LVCMOS SelectI/O-Ultra
standards (see
Table 9
). Drive-strength and slew-rate con-
trols for each output driver minimize bus transients. For
LVDCI and LVDCI_DV2 standards, drive strength and
slew-rate controls are not available.
Figure 7
shows the SSTL2, SSTL3, and HSTL configura-
tions. HSTL can sink current up to 48 mA. (HSTL IV)
All pads are protected against damage from electrostatic
discharge (ESD) and from over-voltage transients. Virtex-II
devices use two memory cells to control the configuration of
an I/O as an input. This is to reduce the probability of an I/O
configured as an input from flipping to an output when sub-
jected to a single event upset (SEU) in space applications.
Prior to configuration, all outputs not involved in configura-
tion are forced into their high-impedance state. The
pull-down resistors and the weak-keeper circuits are inac-
tive. The dedicated pin HSWAP_EN controls the pull-up
resistors prior to configuration. By default, HSWAP_EN is
driven High, which disables the pull-up resistors on user I/O
pins. When HSWAP_EN is driven Low, the pull-up resistors
are activated on user I/O pins.
All Virtex-II IOBs support IEEE 1149.1 compatible bound-
ary-scan testing.
Input Path
The Virtex-II IOB input path routes input signals directly to
internal logic and/or through an optional input flip-flop or
latch, or through the DDR input registers. An optional delay
element at the D-input of the storage element eliminates
pad-to-pad hold time. The delay is matched to the internal
clock-distribution delay of the Virtex-II device, and when
used, ensures that the pad-to-pad hold time is zero.
Each input buffer can be configured to conform to any of the
low-voltage signaling standards supported. In some of
these standards the input buffer utilizes a user-supplied
threshold voltage, V
REF
. The need to supply V
REF
imposes
constraints on which standards can be used in the same
bank. See
I/O Banking
description below.
Output Path
The output path includes a 3-state output buffer that drives
the output signal onto the pad. The output and/or the 3-state
signal can be routed to the buffer directly from the internal
logic or through an output/3-state flip-flop or latch, or
through the DDR output/3-state registers.
Each output driver can be individually programmed for a
wide range of low-voltage signaling standards. In most sig-
naling standards, the output High voltage depends on an
externally supplied V
CCO
voltage. The need to supply V
CCO
imposes constraints on which standards can be used in the
same bank. See
I/O Banking
description below.
I/O Banking
Some of the I/O standards described above require V
CCO
and V
REF
voltages. These voltages are externally supplied
Table 9:
LVTTL and LVCMOS Programmable Currents (Sink and Source)
SelectI/O-Ultra
Programmable Current (Worst-Case Guaranteed Minimum)
LVTTL
2 mA
4 mA
6 mA
8 mA
12 mA
16 mA
24 mA
LVCMOS33
2 mA
4 mA
6 mA
8 mA
12 mA
16 mA
24 mA
LVCMOS25
2 mA
4 mA
6 mA
8 mA
12 mA
16 mA
24 mA
LVCMOS18
2 mA
4 mA
6 mA
8 mA
12 mA
16 mA
n/a
LVCMOS15
2 mA
4 mA
6 mA
8 mA
12 mA
16 mA
n/a
Figure 7:
SSTL or HSTL SelectI/O-Ultra Standards
VCCO
OBUF
VREF
Clamp
Diode
PAD
VCCAUX = 3.3V
VCCINT = 1.5V
DS031_24_100900
ds122_1_1.fm Page 11 Wednesday, January 7, 2004 9:15 PM
相關PDF資料 |
PDF描述 |
|---|---|
| XQ2V3000-4BG575M | QPro Virtex-II 1.5V Military QML Platform FPGAs |
| XQ2V3000-4BG575N | QPro Virtex-II 1.5V Military QML Platform FPGAs |
| XQ2V3000-4BG728M | QPro Virtex-II 1.5V Military QML Platform FPGAs |
| XQ2V3000-4BG728N | QPro Virtex-II 1.5V Military QML Platform FPGAs |
| XQ2V3000-4CF1144M | QPro Virtex-II 1.5V Military QML Platform FPGAs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XQ2V3000-4BG575M | 制造商:XILINX 制造商全稱:XILINX 功能描述:QPro Virtex-II 1.5V Military QML Platform FPGAs |
| XQ2V3000-4BG575N | 制造商:XILINX 制造商全稱:XILINX 功能描述:QPro Virtex-II 1.5V Military QML Platform FPGAs |
| XQ2V3000-4BG728M | 制造商:XILINX 制造商全稱:XILINX 功能描述:QPro Virtex-II 1.5V Military QML Platform FPGAs |
| XQ2V3000-4BG728N | 制造商:XILINX 制造商全稱:XILINX 功能描述:QPro Virtex-II 1.5V Platform FPGAs |
| XQ2V3000-4CF1144M | 制造商:XILINX 制造商全稱:XILINX 功能描述:QPro Virtex-II 1.5V Military QML Platform FPGAs |
發布緊急采購，3分鐘左右您將得到回復。