- 您現在的位置：買賣IC網 > PDF目錄1972 > X9279UV14ZT1 (Intersil)IC XDCP SGL 256TAP 50K 14-TSSOP PDF資料下載
參數資料
| 型號： | X9279UV14ZT1 |
| 廠商： | Intersil |
| 文件頁數： | 15/18頁 |
| 文件大小： | 0K |
| 描述： | IC XDCP SGL 256TAP 50K 14-TSSOP |
| 標準包裝： | 2,500 |
| 系列： | XDCP™ |
| 接片： | 256 |
| 電阻（歐姆）： | 50k |
| 電路數： | 1 |
| 溫度系數： | 標準值 ±300 ppm/°C |
| 存儲器類型： | 非易失 |
| 接口： | I²C（設備位址） |
| 電源電壓： | 4.5 V ~ 5.5 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 14-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 14-TSSOP |
| 包裝： | 帶卷 (TR) |
6
FN8175.4
September 23, 2009
Acknowledge Polling
The disabling of the inputs, during the internal non-volatile
write operation, can be used to take advantage of the typical
5ms EEPROM write cycle time. Once the stop condition is
issued to indicate the end of the non-volatile write command
the X9279 initiates the internal write cycle. ACK Polling
Sequence, Flow 1, can be initiated immediately. This
involves issuing the start condition followed by the device
slave address. If the X9279 is still busy with the write
operation no ACK will be returned. If the X9279 has
completed the write operation an ACK will be returned and
the master can then proceed with the next operation.
Flow 1: ACK Polling Sequence
Instruction and Register Description
Device Addressing: Identification Byte (ID and A)
The first byte sent to the X9279 from the host, following a CS
going HIGH to LOW, is called the Identification byte. The
most significant four bits of the slave address are a device
type identifier. The ID[3:0] bits is the device ID for the X9279;
this is fixed as 0101[B] (refer to Table 3).
The A[2:0] bits in the ID byte is the internal slave address.
The physical device address is defined by the state of the
A2 - A0 input pins. The slave address is externally specified
by the user. The X9279 compares the serial data stream with
the address input state; a successful compare of both
address bits is required for the X9279 to successfully
continue the command sequence. Only the device which
slave address matches the incoming device address sent by
the master executes the instruction. The A2 - A0 inputs can
be actively driven by CMOS input signals or tied to VCC or
VSS.
Instruction Byte (I)
The next byte sent to the X9279 contains the instruction and
register pointer information. The three most significant bits
are used provide the instruction opcode I [2:0]. The RB and
RA bits point to one of the four Data Registers. P0 is the
POT selection; since the X9279 is single POT, the P0 = 0.
The format is shown in Table 4.
Register Bank Selection (RB, RA, P1, P0)
There are 16 registers organized into four banks. Bank 0 is
the default bank of registers. Only Bank 0 registers can be
used for Data Register to Wiper Counter Register
operations.
Banks 1, 2, and 3 are additional banks of registers (12 total)
that can be used for 2-Wire write and read operations. The
Data Registers in Banks 1, 2, and 3 cannot be used for direct
read/write operations between the Wiper Counter Register.
SCL FROM MASTER
1
89
DATA OUTPUT
ACKNOWLEDGE
FIGURE 2. ACKNOWLEGE RESPONSE FROM RECEIVER
FROM TRANSMITTER
FROM RECEIVER
DATA OUTPUT
START
Non-volatile Write
Command Completed
EnterACK Polling
Issue
START
Issue Slave
Address
ACK
Returned?
Further
Operation?
Issue
Instruction
Issue STOP
No
Yes
Proceed
Issue STOP
No
Proceed
X9279
相關PDF資料 |
PDF描述 |
|---|---|
| X9313ZST2 | IC XDCP 32-TAP 1K 3-WIRE 8-SOIC |
| X9314WST2 | IC XDCP SGL 32-TAP 10K 8-SOIC |
| X93154UU8IZ-3 | IC XDCP 32-TAP 50K 3-WIRE 8-MSOP |
| X93155UM8IT1 | IC XDCP 32-TAP 50K 3-WIRE 8-MSOP |
| X93156WM8I-2.7T1 | IC XDCP 32-TAP 12.5K 3WIRE 8MSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X9294DRKT-01 | 功能描述:機架和機柜配件 XPress-Pro 94000 19" Rack Mnt Kit RoHS:否 制造商:Bivar 產品:Rack Accessories 面板空間: 顏色:Black |
| X9294PMKT-01 | 功能描述:機架和機柜配件 XPress-Pro 92000 & 94000 Wall Mnt Kit RoHS:否 制造商:Bivar 產品:Rack Accessories 面板空間: 顏色:Black |
| X92RP4 | 功能描述:消費電池與相機電池 AAA 1350mAh 4 PK Titanium Alkaline RoHS:否 制造商:FDK Batteries 電池大小:CR1/3N 輸出電壓:3 V 容量:160 mAh 化學性質:Lithium 端接類型:Pressure Contacts 可再充電/不可再充電:Non-Rechargeable |
| X92RP6 | 功能描述:消費電池與相機電池 AAA 1375mAh 6 PK Titanium Alkaline RoHS:否 制造商:FDK Batteries 電池大小:CR1/3N 輸出電壓:3 V 容量:160 mAh 化學性質:Lithium 端接類型:Pressure Contacts 可再充電/不可再充電:Non-Rechargeable |
| X92RP8 | 功能描述:消費電池與相機電池 NOT AVAILABLE THROUGH MOUSER RoHS:否 制造商:FDK Batteries 電池大小:CR1/3N 輸出電壓:3 V 容量:160 mAh 化學性質:Lithium 端接類型:Pressure Contacts 可再充電/不可再充電:Non-Rechargeable |
發布緊急采購，3分鐘左右您將得到回復。