- 您現在的位置：買賣IC網 > PDF目錄9412 > X9110TV14IZ-2.7 (Intersil)IC POT DGTL 100K OHM 14-TSSOP PDF資料下載
參數資料
| 型號： | X9110TV14IZ-2.7 |
| 廠商： | Intersil |
| 文件頁數： | 15/18頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC POT DGTL 100K OHM 14-TSSOP |
| 標準包裝： | 95 |
| 系列： | XDCP™ |
| 接片： | 1024 |
| 電阻（歐姆）： | 100k |
| 電路數： | 1 |
| 溫度系數： | 標準值 ±300 ppm/°C |
| 存儲器類型： | 非易失 |
| 接口： | 4 線 SPI（芯片選擇，設備位址） |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 14-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 14-TSSOP |
| 包裝： | 管件 |
| 產品目錄頁面： | 1237 (CN2011-ZH PDF) |
6
FN8158.3
February 13, 2008
TABLE 4. IDENTIFICATION BYTE FORMAT
TABLE 5. INSTRUCTION BYTE FORMAT
Device Instructions
Identification Byte (ID and A)
The first byte sent to the X9110 from the host, following a CS
going HIGH to LOW, is called the Identification Byte. The
most significant four bits of the slave address are a device
type identifier. The ID[3:0] bits is the device ID for the X9110;
this is fixed as 0101[B] (refer to Table 4).
The A0 bit in the ID byte is the internal slave address. The
physical device address is defined by the state of the A0 input
pin. The slave address is externally specified by the user. The
X9110 compares the serial data stream with the address input
state; a successful compare of the address bit is required for
the X9110 to successfully continue the command sequence.
Only the device whose slave address matches the incoming
device address sent by the master executes the instruction.
The A0 input can be actively driven by CMOS input signals or
tied to VCC or VSS. The R/W bit is used to set the device to
either read or write mode.
Instruction Byte and Register Selection
The next byte sent to the X9110 contains the instruction and
register pointer information. The three most significant bits
are used provide the instruction opcode (I[2:0]). The RB and
RA bits point to one of the four registers. The format is
shown in Table 5.
Five of the seven instructions are four bytes in length. These
instructions are:
Read Wiper Counter Register – read the current wiper
position of the selected pot
Write Wiper Counter Register – change current wiper
position of the selected pot
Read Data Register – read the contents of the selected
data register
Write Data Register – write a new value to the selected
data register
Read Status – This command returns the contents of the
WIP bit which indicates if the internal write cycle is in
progress
The basic sequence of the four byte instructions is illustrated
in Figure 3. These four-byte instructions exchange data
between the WCR and one of the Data Registers. A transfer
from a Data Register to a WCR is essentially a write to a
static RAM, with the static RAM controlling the wiper
position. The response of the wiper to this action will be
delayed by tWRL. A transfer from the WCR (current wiper
position), to a Data Register is a write to nonvolatile memory
and takes a minimum of tWR to complete. The transfer can
occur between the potentiometer and one of its associated
registers. The Read Status Register instruction is the only
unique format (see Figure 4).
Two instructions require a two-byte sequence to complete
(See Figure 2). These instructions transfer data between the
host and the X9110; either between the host and one of the
Data Registers or directly between the host and the Wiper
Counter Register. These instructions are:
XFR Data Register to Wiper Counter Register – This
transfers the contents of one specified Data Register to
the associated Wiper Counter Register
XFR Wiper Counter Register to Data Register – This
transfers the contents of the specified Wiper Counter
Register to the specified associated Data Register
See Instruction format for more details.
ID3
ID2
ID1
ID0
0
A0
R/W
01
(MSB)
(LSB)
DEVICE TYPE
IDENTIFIER
INTERNAL SLAVE
ADDRESS
READ OR
WRITE BIT
I2
I1
I0
0
RB
RA
0
(MSB)
(LSB)
INSTRUCTION
OPCODE
REGISTER
SELECTION
RB
RA
REGISTER
0
1
0
1
0
1
DR0
DR1
DR2
DR3
X9110
相關PDF資料 |
PDF描述 |
|---|---|
| MS3108E20-14S | CONN PLUG 5POS RT ANG W/SCKT |
| MAX5464EXT+T | IC POT DGTL 32-TAP 2WIRE SC70-6 |
| MS27484E20F16P | CONN PLUG 16POS STRAIGHT W/PINS |
| MS27474T18F28P | CONN RCPT 28POS JAM NUT W/PINS |
| MAX5468EUT+T | IC POT DGTL 32-TAP 2WIRE SOT23-6 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X9110TV14Z | 功能描述:IC XDCP SGL 1024TAP 100K 14TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:256 電阻（歐姆）:100k 電路數:2 溫度系數:標準值 35 ppm/°C 存儲器類型:易失 接口:6 線串行（芯片選擇，遞增，增/減） 電源電壓:2.6 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
| X9110TV14Z-2.7 | 功能描述:IC XDCP SGL 1024TAP 100K 14TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:256 電阻（歐姆）:100k 電路數:2 溫度系數:標準值 35 ppm/°C 存儲器類型:易失 接口:6 線串行（芯片選擇，遞增，增/減） 電源電壓:2.6 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
| X9110TV14ZT1 | 功能描述:IC XDCP 1024-TAP 100K 14-TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:256 電阻（歐姆）:100k 電路數:2 溫度系數:標準值 35 ppm/°C 存儲器類型:易失 接口:6 線串行（芯片選擇，遞增，增/減） 電源電壓:2.6 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
| X9111 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Single Supply/Low Power/1024-Tap/SPI Bus |
| X9111_06 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Single Digitally-Controlled (XDCP⑩) Potentiometer |
發布緊急采購，3分鐘左右您將得到回復。