- 您現在的位置：買賣IC網 > PDF目錄9412 > X9110TV14IZ-2.7 (Intersil)IC POT DGTL 100K OHM 14-TSSOP PDF資料下載
參數資料
| 型號： | X9110TV14IZ-2.7 |
| 廠商： | Intersil |
| 文件頁數： | 12/18頁 |
| 文件大小： | 0K |
| 描述： | IC POT DGTL 100K OHM 14-TSSOP |
| 標準包裝： | 95 |
| 系列： | XDCP™ |
| 接片： | 1024 |
| 電阻（歐姆）： | 100k |
| 電路數： | 1 |
| 溫度系數： | 標準值 ±300 ppm/°C |
| 存儲器類型： | 非易失 |
| 接口： | 4 線 SPI（芯片選擇，設備位址） |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 14-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 14-TSSOP |
| 包裝： | 管件 |
| 產品目錄頁面： | 1237 (CN2011-ZH PDF) |
3
FN8158.3
February 13, 2008
Circuit Level Applications
Vary the gain of a voltage amplifier
Provide programmable dc reference voltages for
comparators and detectors
Control the volume in audio circuits
Trim out the offset voltage error in a voltage amplifier
circuit
Set the output voltage of a voltage regulator
Trim the resistance in Wheatstone bridge circuits
Control the gain, characteristic frequency and Q-factor in
filter circuits
Set the scale factor and zero point in sensor signal
conditioning circuits
Vary the frequency and duty cycle of timer ICs
Vary the dc biasing of a pin diode attenuator in RF circuits
Provide a control variable (I, V, or R) in feedback circuits
System Level Applications
Adjust the contrast in LCD displays
Control the power level of LED transmitters in
communication systems
Set and regulate the DC biasing point in an RF power
amplifier in wireless systems
Control the gain in audio and home entertainment systems
Provide the variable DC bias for tuners in RF wireless
systems
Set the operating points in temperature control systems
Control the operating point for sensors in industrial
systems
Trim offset and gain errors in artificial intelligent systems
Bus Interface Pins
SERIAL OUTPUT (SO)
SO is a serial data output pin. During a read cycle, data is
shifted out on this pin. Data is clocked out on the falling edge
of the serial clock.
SERIAL INPUT (SI)
SI is the serial data input pin. All opcodes, byte addresses
and data to be written to the pots and pot registers are input
on this pin. Data is latched by the rising edge of the serial
clock.
SERIAL CLOCK (SCK)
The SCK input is used to clock data into and out of the
X9110.
HOLD (HOLD)
HOLD is used in conjunction with the CS pin to select the
device. Once the part is selected and a serial sequence is
underway, HOLD may be used to pause the serial
communication with the controller without resetting the serial
sequence. To pause, HOLD must be brought LOW while SCK is
LOW. To resume communication, HOLD is brought HIGH, again
while SCK is LOW. If the pause feature is not used, HOLD should
be held HIGH at all times.
DEVICE ADDRESS (A0)
The address input is used to set the 8-bit slave address. A
match in the slave address serial data stream A0 must be
made with the address input (A0) in order to initiate
communication with the X9110.
CHIP SELECT (CS)
When CS is HIGH, the X9110 is deselected and the SO pin
is at high impedance, and (unless an internal write cycle is
underway) the device will be in the standby state. CS LOW
enables the X9110, placing it in the active power mode. It
should be noted that after a power-up, a HIGH to LOW
transition on CS is required prior to the start of any
operation.
HARDWARE WRITE PROTECT INPUT (WP)
The WP pin when LOW prevents nonvolatile writes to the
Data Registers.
Pin Descriptions
PIN
(TSSOP)
SYMBOL
FUNCTION
1
V+
Analog Supply Voltage
2
SO
Serial Data Output
3
A0
Device Address
4
SCK
Serial Clock
5WP
Hardware Write Protect
6
SI
Serial Data Input
7VSS
System Ground
8V
-
Analog Supply Voltage
9CS
Chip Select
10
HOLD
Device Select. Pause the Serial Bus
11
RW
Wiper Terminal of the Potentiometer
12
RH
High Terminal of the Potentiometer
13
RL
Low Terminal of the Potentiometer
14
VCC
System Supply Voltage
Pin Descriptions (Continued)
PIN
(TSSOP)
SYMBOL
FUNCTION
X9110
相關PDF資料 |
PDF描述 |
|---|---|
| MS3108E20-14S | CONN PLUG 5POS RT ANG W/SCKT |
| MAX5464EXT+T | IC POT DGTL 32-TAP 2WIRE SC70-6 |
| MS27484E20F16P | CONN PLUG 16POS STRAIGHT W/PINS |
| MS27474T18F28P | CONN RCPT 28POS JAM NUT W/PINS |
| MAX5468EUT+T | IC POT DGTL 32-TAP 2WIRE SOT23-6 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X9110TV14Z | 功能描述:IC XDCP SGL 1024TAP 100K 14TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:256 電阻（歐姆）:100k 電路數:2 溫度系數:標準值 35 ppm/°C 存儲器類型:易失 接口:6 線串行（芯片選擇，遞增，增/減） 電源電壓:2.6 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
| X9110TV14Z-2.7 | 功能描述:IC XDCP SGL 1024TAP 100K 14TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:256 電阻（歐姆）:100k 電路數:2 溫度系數:標準值 35 ppm/°C 存儲器類型:易失 接口:6 線串行（芯片選擇，遞增，增/減） 電源電壓:2.6 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
| X9110TV14ZT1 | 功能描述:IC XDCP 1024-TAP 100K 14-TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:256 電阻（歐姆）:100k 電路數:2 溫度系數:標準值 35 ppm/°C 存儲器類型:易失 接口:6 線串行（芯片選擇，遞增，增/減） 電源電壓:2.6 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
| X9111 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Single Supply/Low Power/1024-Tap/SPI Bus |
| X9111_06 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Single Digitally-Controlled (XDCP⑩) Potentiometer |
發布緊急采購，3分鐘左右您將得到回復。