- 您現在的位置：買賣IC網 > PDF目錄376444 > x60250 (Intersil Corporation) Micro Power Programmable Voltage Reference(微功耗可編程電壓基準) PDF資料下載
參數資料
| 型號： | x60250 |
| 廠商： | Intersil Corporation |
| 英文描述： | Micro Power Programmable Voltage Reference(微功耗可編程電壓基準) |
| 中文描述： | 微功率可編程電壓參考（微功耗可編程電壓基準） |
| 文件頁數： | 10/16頁 |
| 文件大小： | 382K |
| 代理商： | X60250 |
10
FN8146.1
September 14, 2005
X60250 BUS INTERFACE INFORMATION
Slave Address, Address Byte, and Data Byte
The byte communication format for the serial bus is
shown in Figure 1 on the previous page. The first byte,
BYTE 0, defines the device identifier, 0101 in the upper
half; and the device slave address in the low half of the
byte. The slave address is set to 0. The next byte,
BYTE 1, is the Address Byte. The Address Byte
identifies a unique address for the Status or Control
Registers as shown in the Register Descriptions table.
The following byte, Byte 2, is the byte used for READ
and WRITE operations.
Start Condition
All commands are preceded by the start condition, which
is a HIGH to LOW transition of SDA when SCL is HIGH.
The device continuously monitors the SDA and SCL
lines for the start condition and will not respond to any
command until this condition has been met. On power-
up, the SCL pin must be brought LOW prior to the
START condition. See Figure 3.
Stop Condition
All communications must be terminated by a stop
condition, which is a LOW to HIGH transition of SDA
when SCL is HIGH followed by a HIGH to LOW
transistion on SCL. After going LOW, SCL can stay LOW
or return to HIGH. See Figure 3.
Acknowledge
Acknowledge is a software convention used to indicate
successful data transfer. The transmitting device, either
master or slave, will release the bus after transmitting
eight bits. During the ninth clock cycle, the receiver will
pull the SDA line LOW to acknowledge that it received
the eight bits of data. Refer to Figure 4. The device will
respond with an acknowledge after recognition of a start
condition and if the correct Device Identifier and Select
bits are contained in the Slave Address Byte. If a write
operation is selected, the device will respond with an
acknowledge after the receipt of each subsequent eight
bit word. The device will acknowledge all incoming data
and address bytes, except for:
– The Slave Address Byte when the Device Identifier
and/or Select bits are incorrect
– The 2nd Data Byte of a Status Register Write Oper-
ation (only 1 data byte is allowed)
Pin Descriptions
V
REFOUT
Reference voltage output. The 1.25V bandgap
reference output (V
REF
) is available at this pin for
application to other circuits. Maximum output current is
400μA. The V
REFOUT
pin also connects to the Rh
terminal of the 256-tap DCP.
V
OUT
DCP Wiper Output. This pin functions as the wiper of the
DCP, and can be used as a variable voltage source for
voltages between GND and V
REF
. Since it is connected
to the DCP resistor, any loads on this pin must be high
impedance for best performance.
R
1
Auxiliary Resistor Input. The R
1
pin is connected to one
end of a 100k
resistor (R
1
) which closely matches the
DCP resistance. The other end of R
1
is tied to the R
REFL
terminal of the DCP. When R
1
is grounded and V
REFL
is
left open, the output voltage range of V
OUT
will be from
V
REF
/2 to V
REF
, and the effective resolution (mV/step) of
the Reference control is doubled. R
1
should be left open
if not used.
GND
This pin is common for the V
REF
output and for control
signal inputs.
SDA
Serial Data Input/Output. Bidirectional pin used for serial
data transfer. As an output, it is open drain and may be
wire-ored with any number of open drain or open
collector outputs. A pullup resistor is required and the
value is dependent on the speed of the serial data bus
and the number of outputs tied together.
SCL
Serial Clock Input. Accepts a clock signal for clocking
serial data into and out of the device.
V
REFL
DCP and Auxiliary Resistor Input. This pin is connected
to one end of the 256-tap DCP, and also to one end of
the 100k
auxiliary resistor. When connected to ground,
V
OUT
range will be from 0V to V
REF
. When left open
and R
1
is connected to ground, the voltage at this pin will
be from V
REF
/2 to V
REF
.
X60250
相關PDF資料 |
PDF描述 |
|---|---|
| X60250V8I | Micro Power Programmable Voltage Reference |
| X60250V8IZ | Micro Power Programmable Voltage Reference |
| X79002 | NV DAC with Selectable Output Range and Memory |
| X79000 | NV DAC with Selectable Output Range and Memory |
| X79000V20I | NV DAC with Selectable Output Range and Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X60250V8I | 功能描述:IC VREF SERIES ADJ 8-TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 電壓基準 系列:- 標準包裝:3,000 系列:- 基準類型:旁路，精度 輸出電壓:5V 容差:±0.5% 溫度系數:100ppm/°C 輸入電壓:- 通道數:1 電流 - 陰極:80µA 電流 - 靜態:- 電流 - 輸出:15mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:TO-236-3，SC-59，SOT-23-3 供應商設備封裝:SOT-23-3 包裝:帶卷 (TR) 其它名稱:LM4040CIM3-5.0MLTRLM4040CIM3-5.0MLTR-ND |
| X60250V8IZ | 功能描述:IC VREF SERIES ADJ 8-TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電壓基準 系列:- 標準包裝:1 系列:- 基準類型:串聯，精度 輸出電壓:4.5V 容差:±800µV 溫度系數:1ppm/°C 輸入電壓:13.5 V ~ 22 V 通道數:1 電流 - 陰極:- 電流 - 靜態:7mA 電流 - 輸出:10mA 工作溫度:-55°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:20-LCC 供應商設備封裝:20-CLCC 包裝:管件 |
| X60M000000L006 | 制造商:AEL Crystals Limited 功能描述:CRYSTAL 60MHZ HC49/U |
| X60R75 | 制造商:Teledyne Relays 功能描述:RELAY SSR 30MA 30V DC-IN 75A 690V AC-OUT 4-PIN - Bulk 制造商:Teledyne Industrial 功能描述: 制造商:Teledyne Relays 功能描述:SOLID STATE RELAY |
發布緊急采購，3分鐘左右您將得到回復。