- 您現在的位置：買賣IC網 > PDF目錄372534 > X4C105 RTC Module With CPU Supervisor PDF資料下載
參數資料
| 型號： | X4C105 |
| 元件分類： | CPU監測 |
| 英文描述： | RTC Module With CPU Supervisor |
| 中文描述： | 時鐘模塊CPU監控 |
| 文件頁數： | 8/18頁 |
| 文件大?。?/td> | 93K |
| 代理商： | X4C105 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁
X4C105
8
The device offers a similar operation, called “Set Current
Address,” where the device ends the transmission and
issues a stop instead of the second start, shown in figure
10. The device goes into standby mode after the stop
and all bus activity will be ignored until a start is detected.
This operation loads the new address into the address
counter. The next Current Address Read operation will
then read from the newly loaded address. This operation
could be useful if the master knows the next address it
needs to read, but is not ready for the data.
Sequential Read
Sequential reads can be initiated as either a current
address read or random address read. The first Data
Byte is transmitted as with the other modes; however, the
master now responds with an acknowledge, indicating it
requires additional data. The device continues to output
data for each acknowledge received. The master
terminates the read operation by not responding with an
acknowledge and then issuing a stop condition.
The data output is sequential, with the data from address
n followed by the data from address n + 1. The address
counter for read operations increments through all page
and column addresses, allowing the entire memory
contents to be serially read during one operation. At the
end of the address space the counter “rolls over” to
address 0000
H
and the device continues to output data
for each acknowledge received. Refer to figure 11 for the
acknowledge and data transfer sequence.
Serial Device Addressing
Slave Address Byte
Following a start condition, the master must output a
Slave Address Byte. This byte consists of several parts:
— a device type identifier that is always ‘1010’.
— two bits that provide the device select bits.
— one bit that becomes the MSB of the address.
— one bit of the slave command byte is a R/W bit. The
R/W bit of the Slave Address Byte defines the opera-
tion to be performed. When the R/W bit is a one, then
a read operation is selected. A zero selects a write
operation. Refer to Figure 12.
S
t
a
r
t
S
t
o
p
Slave
Address
Data
A
C
K
SDA Bus
Signals from
the Slave
Signals from
the Master
1
Figure 9. Current Address Read Sequence
0
Slave
Address
Byte Address
A
C
K
A
C
K
S
t
a
r
t
S
t
o
p
Slave
Address
Data
A
C
K
1
S
t
a
r
t
SDA Bus
Signals from
the Slave
Signals from
the Master
Figure 10. Random Address Read Sequence
相關PDF資料 |
PDF描述 |
|---|---|
| X4ODC5R | |
| X4ODC5R5 | 16MHZ, TQFP, IND TEMP, 5V(MCU AVR) |
| X5045(中文) | RTC Module With CPU Supervisor |
| X5043(中文) | 512×8Bit CPU Supervisor with 4K SPI EEPROM(帶4Kb SPI EEPROM的CPU監控器) |
| X5163(中文) | RTC Module With CPU Supervisor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X4C105V20 | 功能描述:IC SUPERVISOR NOVRAM/EE 20-TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
| X4C105V20-3A | 功能描述:IC SUPERVISOR NOVRAM/EE 20-TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
| X4C105V20-3AT1 | 功能描述:IC SUPERVISOR NOVRAM/EE 20-TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
| X4C105V20-3C7889 | 制造商:Intersil Corporation 功能描述: |
| X4C105V20I | 功能描述:IC SUPERVISOR NOVRAM/EE 20-TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。