參數資料
型號: VV5404C001
廠商: 意法半導體
英文描述: Mono and Colour Digital Video CMOS Image Sensors
中文描述: 莫諾和數字視頻彩色CMOS圖像傳感器
文件頁數: 18/54頁
文件大?。?/td> 786K
代理商: VV5404C001
VV5404 & VV6404
CD5404-6404F-A
18/54
4.6.1 Power-Up/Down (Figure 12)
On power-up all of the databus lines will go high Immediately (F
H
), to indicate that the device is “present” and the
device enters it low-power mode (Section 4.6.2).
When the Video Processor is reset the following sequence should be executed to ensure that the VM6404 starts to
generate video data:
1. After the Video Processor has been released from reset, the sensor clock, CLKI, should be enabled immedi-
ately
2. After waiting for at least 16 CLKI clock cycles, a “Soft Reset” command should be issued to the sensor. This is
necessary to ensure that the sensor is brought into a known state. If the sensor is not present then the serial
interface communications by Video Processor will not be acknowledged.
3. Poll for 32 consecutive F
H
values on the data bus, if this condition is satisfied then the sensor is present. The
Video processor should set the camera_present flag.
4. Determine if the serial CMOS E
2
PROM containing the defectivity map for the sensor is present and down-load
the values.
5. Disable the sensor clock CKI.
6. The Video Processor should generate the VP_Ready interrupt.
7. Once the host software serviced the VP_Ready interrupt, then the sensor and video processor is ready to gen-
erate video data.
8. To enable video data, the host software, sets the low-power mode bit low. The video processor must enable
CLKI at least 16 CLKI clock cycles before issuing the “Exit Low-Power Mode” command via the serial interface.
After the “Exit Low-Power Mode” command has been sent the sensor will output for one frame, a continuous stream
of alternating 9
H
and 6
H
values on D[3:0]. By locking onto the resulting 0101/1010 patterns appearing on the data bus
lines the video processor can determine the best sampling position for the nibble data. After the last 9
H
6
H
pair has
been output the databus returns to F
H
until the start of fifth frame after CKI has been enabled when the first active
frame output. After the video processor has determined the correct sampling position for the data, it should then wait
for the next start of frame line (SOF).
If the video processor detects 32 consecutive 0
H
values on the data bus, then the sensor has been removed. The
sensor clock, CKI, should be held low.
4.6.2
Under the control of the serial interface the sensor analogue circuitry can be powered down and then be powered up.
When the low-power bit is set via the serial interface, all the databus lines will go high at the end of the end of frame
line of the current frame. At this point the analogue circuits in the sensor will power down. The system clock must
remain active for the duration of low power mode.
Only the analogue circuits are powered down, the values of the serial interface registers e.g. exposure and gain are
preserved.
The internal frame timing is reset to the start of a video frame on exiting low-power mode.
In a similar manner to the previous section, the first frame after the serial comms contains a continuous stream of
alternating 9
H
and 6
H
to allow the video processor to re-confirm its sampling position. Then three frames latter the
first start of frame line is generated.
Low-Power Mode (Figure 10)
4.6.3
Sleep mode is similar to the low-power mode, except that analogue circuitry remains powered. When the sleep
command is received via the serial interface the pixel array will be put into reset and the data lines all will go high at
the end of the current frame. Again the system clock must remain active for the duration of sleep mode.
When sleep mode is disabled, the CMOS sensor’s frame timing is reset to the start of a frame. During the first frame
after exiting from sleep mode the databus will remain high, while the exposure value propagates through the pixel
array. At the start of the second frame the first start of field line will be generated.
Sleep Mode (Figure 11)
相關PDF資料
PDF描述
VV5404 CIF FORMAT DIGITAL IMAGE SENSOR
VV5410 Mono and Colour Digital Video CMOS Image Sensors
VV5430C001 Monochrome Analog Output CMOS Image Sensors
VV5430 Integrated CMOS Image Sensor with support for ADC and external control via serial interface
VV6410C036 DUAL-MODE DIGITAL CAMERA CHIPSET
相關代理商/技術參數
參數描述
VV5410 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Mono and Colour Digital Video CMOS Image Sensors
VV5410C036 制造商:STMicroelectronics 功能描述:IMAGE SENSOR MONOCHROME CMOS 352X288PIXELS 36CLCC - Bulk
VV5430 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Integrated CMOS Image Sensor with support for ADC and external control via serial interface
VV5430C001 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Monochrome Analog Output CMOS Image Sensors
VV5501C001 功能描述:視頻 IC Monochrome Sensor RoHS:否 制造商:Fairchild Semiconductor 工作電源電壓:5 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-28 封裝:Reel