- 您現在的位置：買賣IC網 > PDF目錄359787 > VSC7129 (Vitesse Semiconductor Corporation.) Toggle Switch; No. of Switch Positions:10; Circuitry:SPST; Contact Current Max:1.5A; Mounting Type:PCB; Number of Positions:10; Switch Function:SPST PDF資料下載
參數資料
| 型號： | VSC7129 |
| 廠商： | Vitesse Semiconductor Corporation. |
| 英文描述： | Toggle Switch; No. of Switch Positions:10; Circuitry:SPST; Contact Current Max:1.5A; Mounting Type:PCB; Number of Positions:10; Switch Function:SPST |
| 中文描述： | 家庭的中繼/重定時器和端口旁路電路的光纖通道 |
| 文件頁數： | 1/12頁 |
| 文件大小： | 174K |
| 代理商： | VSC7129 |
Data Sheet
VSC7127/VSC7129
Family of Repeater/Retimer and Port
Bypass Circuits for Fibre Channel
G52298-0, Rev 4.3
05/01/01
Page 1
VITESSE
SEMICONDUCTOR CORPORATION
741 Calle Plano Camarillo, CA 93012
Tel: (800) VITESSE FAX: (805) 987-5896 Email: prodinfo@vitesse.com
Internet: www.vitesse.com
VITESSE
Features
ANSI X3T11 Fibre Channel Compliant
General Description
The VSC7127 and VSC7129 contain six cascaded Port Bypass Circuits (PBCs), the FibreTimer
config-
urable Repeater/Retimer (CRU) and a Signal Detect Unit (SDU). These parts are typically used in distributing
Fibre Channel signals to an array of disk drives in an FC-AL loop as illustrated in Figure 1. The first
VSC7127
’
s CRU is configured as a Repeater to attenuate jitter, the second VSC7127
’
s CRU is bypassed to
reduce power and the third VSC7127
’
s CRU is configured as a retimer so that the output of the device is a jitter-
compliance point.
Each PBC is a multiplexer that is controlled by the corresponding SELx line which, if HIGH, selects the
external input or, if LOW, selects the output of the previous PBC. For the VSC712xR, when MODE is LOW
and SEL5 is HIGH, the CRU is a sophisticated repeater which has low latency, no peaking and attenuates jitter
even at low frequencies. When MODE is HIGH and SEL5 is HIGH, the CRU is a retimer which eliminates jit-
ter transfer but has increased latency due to an elasticity buffer which adds/drops Fibre Channel fill words in
order to accomodate the difference between the baud rate of the incoming data and the local REFCLK. When
SEL5 is LOW, the CRU is bypassed and powered down. The SDU monitors the analog levels of the IO+/- input
and monitors the output of the CRU digitally to indicate whether valid data is present.
The VSC7127/VSC7129 are similar to the VSC7124 which does not contain the FibreTimer
cell or CMU.
VSC7127/VSC7129 Block Diagram
1.0625Gb/s Operation
Features the FibreTimer
Configurable Clock
Recovery Unit (CRU): Repeater, Retimer or
Bypassed
Six Port Bypass Circuits (PBC)
Analog/Digital Signal Detect (SDU)
On-Chip Transmit Termination
3.3V, 700mW Power Dissipation
Compatible with HDMP-0451 (VSC7127) or
HDMP-0452 (VSC7129)
44-Pin, 10mm PQFP Package
I
I
O
S
1
0
PBC1
REFCLK
106.25MHz
SDU
CRU
I
I
O
O
S
1
0
PBC2
I
I
O
O
S
1
0
PBC3
I
I
O
O
S
1
0
PBC4
CMU
SIGDET
0.1uF
MODE
O
I
I
O
O
S
1
0
PBC0
0
1
PBC5
SEL5
相關PDF資料 |
PDF描述 |
|---|---|
| VSC7129R | Family of Repeater/Retimer and Port Bypass Circuits for Fibre Channel |
| VSC7129T | Family of Repeater/Retimer and Port Bypass Circuits for Fibre Channel |
| VSC7186TW | Quad Transceiver for Gigabit Ethernet |
| VSC7216UC-01 | Multi-Gigabit Interconnect Chip |
| VCC6-LAA-622M080 | 3.3 volt LVDS Oscillator, >270MHz |
相關代理商/技術參數 |
參數描述 |
|---|---|
| VSC7129R | 制造商:VITESSE 制造商全稱:Vitesse Semiconductor Corporation 功能描述:Family of Repeater/Retimer and Port Bypass Circuits for Fibre Channel |
| VSC7129T | 制造商:VITESSE 制造商全稱:Vitesse Semiconductor Corporation 功能描述:Family of Repeater/Retimer and Port Bypass Circuits for Fibre Channel |
| VSC7130RC | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecomm/Datacomm |
| VSC7132 | 制造商:VITESSE 制造商全稱:Vitesse Semiconductor Corporation 功能描述:Link Replicator for Fibre Channel, Gigabit Ethernet and HDTV |
| VSC7132-01 | 制造商:VITESSE 制造商全稱:Vitesse Semiconductor Corporation 功能描述:Link Replicator for Fibre Channel, Gigabit Ethernet and HDTV |
發布緊急采購，3分鐘左右您將得到回復。