- 您現在的位置：買賣IC網 > PDF目錄225499 > V62/05616-01XE (TEXAS INSTRUMENTS INC) 2.2 A SWITCHING CONTROLLER, 1150 kHz SWITCHING FREQ-MAX, PDSO16 PDF資料下載
參數資料
| 型號： | V62/05616-01XE |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | 2.2 A SWITCHING CONTROLLER, 1150 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封裝： | GREEN, PLASTIC, SOIC-16 |
| 文件頁數： | 20/21頁 |
| 文件大?。?/td> | 447K |
| 代理商： | V62/05616-01XE |
t
LEB + 0.5
R 10 kW
C
(2)
UDG95105
CT
CLK/LEB
LEB
RAMP
Input
Blanked
RAMP
to PWM
SGLS305D – JULY 2005 – REVISED SEPTEMBER 2010
www.ti.com
Leading-Edge Blanking (LEB)
The UC2825A-EP performs fixed-frequency PWM control. The UC2825A-EP outputs are alternately controlled.
During every other cycle, one output is off. Each output then switches at one-half the oscillator frequency, varying
in duty cycle from 0 to less than 50%.
To limit maximum duty cycle, the internal clock pulse blanks both outputs low during the discharge time of the
oscillator. On the falling edge of the clock, the appropriate output(s) is driven high. The end of the pulse is
controlled by the PWM comparator, current-limit comparator, or the overcurrent comparator.
Normally the PWM comparator senses a ramp crossing a control voltage (error-amplifier output) and terminates
the pulse. LEB causes the PWM comparator to be ignored for a fixed amount of time after the start of the pulse.
This allows noise inherent with switched-mode power conversion to be rejected. The PWM ramp input may not
require any filtering as a result of LEB.
To program an LEB period, connect a capacitor, C, to CLK/LEB. The discharge time set by C and the internal
10-k
resistor determines the blanked interval. The 10-k resistor has a 10% tolerance. For more accuracy, an
external 2-k
1% resistor (R) can be added, resulting in an equivalent resistance of 1.66 k with a tolerance of
2.4%. The design equation is:
Values of R less than 2 k
should not be used.
LEB also is applied to the current-limit comparator. After LEB, if the ILIM pin exceeds the 1-V threshold, the
pulse is terminated. The overcurrent comparator, however, is not blanked. It catches catastrophic overcurrent
faults without a blanking delay. Any time the ILIM pin exceeds 1.2 V, the fault latch is set, and the outputs are
driven low. For this reason, some noise filtering may be required on the ILIM pin.
Figure 4. LEB Operational Waveforms
8
Copyright 2005–2010, Texas Instruments Incorporated
Product Folder Link(s): UC2825A-EP
相關PDF資料 |
PDF描述 |
|---|---|
| V62/06636-02XE | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO3 |
| V62/08610-01YB | SWITCHING CONTROLLER, 700 kHz SWITCHING FREQ-MAX, PDSO16 |
| V62/08610-01XB | SWITCHING CONTROLLER, 700 kHz SWITCHING FREQ-MAX, PQCC16 |
| V62C1802048L-100V | 256K X 8 STANDARD SRAM, 100 ns, PDSO32 |
| V62C31864L-35F | 8K X 8 STANDARD SRAM, 35 ns, PDSO28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| V6207602-01XE | 制造商:TI 制造商全稱:Texas Instruments 功能描述:4 ppm100 A SOT23-6 SERIES VOLTAGE REFERENCES |
| V6207602-02XE | 制造商:TI 制造商全稱:Texas Instruments 功能描述:4 ppm100 A SOT23-6 SERIES VOLTAGE REFERENCES |
| V6207602-03XE | 制造商:TI 制造商全稱:Texas Instruments 功能描述:4 ppm100 A SOT23-6 SERIES VOLTAGE REFERENCES |
| V6207602-04XE | 制造商:TI 制造商全稱:Texas Instruments 功能描述:4 ppm100 A SOT23-6 SERIES VOLTAGE REFERENCES |
| V6207602-05XE | 制造商:TI 制造商全稱:Texas Instruments 功能描述:4 ppm100 A SOT23-6 SERIES VOLTAGE REFERENCES |
發布緊急采購，3分鐘左右您將得到回復。