- 您現在的位置：買賣IC網 > PDF目錄359312 > V23806-A8-C1 (INFINEON TECHNOLOGIES AG) Multimode 1300 nm LED Fast Ethernet/FDDI/ATM 10 dB 155 MBd 1x9 Transceiver PDF資料下載
參數資料
| 型號： | V23806-A8-C1 |
| 廠商： | INFINEON TECHNOLOGIES AG |
| 英文描述： | Multimode 1300 nm LED Fast Ethernet/FDDI/ATM 10 dB 155 MBd 1x9 Transceiver |
| 中文描述： | 多模1300納米發光快速以太網/光纖分布式數據介面/ ATM的10分貝，155 MBd的1x9收發器 |
| 文件頁數： | 2/3頁 |
| 文件大?。?/td> | 262K |
| 代理商： | V23806-A8-C1 |
Fiber Optics
V23806-A8-C1, Multimode 1300 nm LED ATM 10 dB 155 MBd 1x9 Transceiver
2
The data rate is scalable and the ATM protocol is the basis of
the broadband public networks being standardized in the Inter-
national Telegraph and Telephone Consultative Committee
(CCITT). ATM can also be used in local private applications.
FDDI is a Dual Token Ring standard developed in the U.S. by the
Accredited National Standards Committee (ANSC) X3T9, within
the Technical Committee X3T9.5. It is applied to the local area
networks of stations, transferring data at 100 Mbits/s with a
125 MBaud transmission rate. LCF FDDI is specially developed
for short distance applications of up to 500 m (fiber-to-the-desk)
as compared to 2 km for backbone applications.
Fast Ethernet was developed because of the higher bandwidth
requirement in local area networking. It is based on the proven
effectiveness of millions of installed Ethernet systems.
The Infineon multimode transceiver is a single unit comprised
of a transmitter, a receiver, and an SC receptacle. This design
frees the customer from many alignment and PC board layout
concerns. The modules are designed for low cost applications.
TECHNICAL DATA
The electro-optical characteristics described in the following
tables are valid only for use under the recommended operating
conditions.
Recommended Operating Conditions
Notes
1. For V
CC
–V
EE
(min., max.). 50% duty cycle. The supply current
(I
CC2
+I
CC3
) does not include the load drive current (Icc1). Add max.
45 mA for the three outputs. Load is 50
into V
CC
–2V.
2. To maintain good LED reliability, the device should not be held in the
ON state for more than the specified time. Normal operation should
be done with 50% duty cycle.
3. To achieve proper PECL output levels the 50
termination should be
done to V
CC
–2 V. For correct termination see the application notes.
Transmitter Electro-Optical Characteristics
Notes
1. Measured at the end of 5 meters of 62.5/125/0.275 graded index
fiber using calibrated power meter and a precision test ferrule.
Cladding modes are removed. Values valid for EOL and worst-case
temperature.
2. The input data pattern is a 12.5 MHz square wave pattern.
3. Center wavelength is defined as the midpoint between the two
50% levels of the optical spectrum of the LED.
4. Spectral width (full width, half max) is defined as the difference
between 50% levels of the optical spectrum of the LED.
5. 10% to 90% levels. Measured using the 12.5 MHz square wave
pattern with an optoelectronic measurement system (detector
and oscilloscope) having 3 dB bandwidth ranging from less than
0.1 MHz to more than 750 MHz.
6. Extinction Ratio is defined as PL/PH x 100%. Measurement system
as in Note 5.
7 Test method as for FDDI-PMD. Jitter values are peak-to-peak.
8. Duty Cycle Distortion is defined as 0.5 [(width of wider state) minus
(width of narrower state)]. It is measured with stream of Idle
Symbols (62.5 MHz square wave).
9. Measured with the same pattern as for FDDI-PMD.
10.Measured with the Halt Line state (12.5 MHz square wave).
Parameter
Symbol
Min.
Typ. Max.
Units
°
C
V
Ambient Temperature
T
AMB
V
CC–
V
EE
I
CC
0
70
Power Supply Voltage
Supply Current +5 V
(1)
Transmitter
4.75
5.0
5.25
140
170
210
mA
Data Input
High Voltage
V
IH
–V
CC
–1165
–880
mV
Data Input
Low Voltage
V
IL
–V
CC
–1810
–1475 mV
Input Data Rise/Fall,
20%–80%
Data High Time
(2)
t
R
, t
F
0.4
1.3
ns
t
on
1000
Receiver
Output Current
l
O
t
DCD
25
mA
Input Duty Cycle
Distortion
1.0
ns
Input Data
Dependent Jitter
t
DDj
Input Random Jitter
t
RJ
l
C
0.76
Input Center
Wavelength
1260
1380
nm
Electrical Output
Load
(3)
R
L
50
W
Transmitter
Symbol
Min.
Typ. Max. Units
Data Rate
DR
200
MBd
Launched Power (Average)
into 62.5
μ
m Fiber
(1, 2)
Center Wavelength
(2, 3)
Spectral Width (FWHM)
(2, 4)
D
l
Output Rise/Fall Time,
10%–90%
(2, 5)
P
O
–20
–17
–14
dBm
λ
C
1270
1360
nm
200
t
R
, t
F
0.6
2.5
ns
Extinction Ratio
(Dynamic)
(2, 6)
ER
10
%
Overshoot
Duty Cycle Distortion
(7 8)
Data Dependent Jitter
(7 9)
Random Jitter
(7 10)
OS
10
%
t
DCD
t
DDJ
t
RJ
0.6
ns
0.3
0.6
相關PDF資料 |
PDF描述 |
|---|---|
| V23806-S84-Z3 | Testboard for ATM, ESCON, Fibre Channel and Gigabit Ethernet 1x9 Transceivers |
| V23806-S84-Z4 | Testboard for ATM, ESCON, Fibre Channel and Gigabit Ethernet 1x9 Transceivers |
| V23809-C8-C10 | Multimode 1300 nm LED Fast Ethernet/FDDI/ATM 170 MBd 1x9 Transceiver |
| V23809-C8-T10 | Multimode 1300 nm LED Fast Ethernet/FDDI/ATM 170 MBd 1x9 Transceiver with ST? Connector |
| V23809-F7-C10 | Multimode 1300 nm LED Fibre Channel 266 MBd Transceiver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| V23806-S84-Z3 | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:Testboard for ATM, ESCON, Fibre Channel and Gigabit Ethernet 1x9 Transceivers |
| V23806-S84-Z4 | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:Testboard for ATM, ESCON, Fibre Channel and Gigabit Ethernet 1x9 Transceivers |
| V23809B7C10 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:FIBER OPTIC TRANSCEIVER |
| V23809C8C10 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| V23809-C8-C10 | 制造商:Infineon Technologies AG 功能描述:MULTIMODE 1300 NM LED FAST ETHERNET/FDDI/ATM 170 MBD 1X9 TRANSCEIVER 制造商:Rochester Electronics LLC 功能描述:- Bulk |
發布緊急采購，3分鐘左右您將得到回復。