參數資料
型號: USB2513-AEZG
廠商: STANDARD MICROSYSTEMS CORP
元件分類: 總線控制器
中文描述: UNIVERSAL SERIAL BUS CONTROLLER, QCC36
封裝: 6 X 6 MM, 0.50 MM PITCH, ROHS COMPLIANT, QFN-36
文件頁數: 51/76頁
文件大?。?/td> 1924K
代理商: USB2513-AEZG
USB 2.0 Hi-Speed Hub Controller
Datasheet
SMSC USB251x
55
Revision 1.1 (04-26-10)
DATASHEET
8.3.9
SMBus Alert Response Address
The SMBALERT# signal is not supported by the hub.
8.3.9.1
Undefined Registers
The registers shown in Table 8.2 are the defined registers in the hub. Reads to undefined registers
return 00h. Writes to undefined registers have no effect and do not return an error.
8.3.9.2
Reserved Registers
Reserved registers should be written to ‘0’ unless otherwise specified. Contents read should be
ignored.
8.4
Default Configuration Option
To configure the SMSC hub in its default configuration, strap CFG_SEL[2:0] to 00h. This procedure
configures the hub to the internal defaults and enables the strapping options. Please see Section 8.2.1,
"Internal Register Set (Common to EEPROM and SMBus)" for the list of the default values. For specific
pin strapping options, please see Chapter 5, Pin Descriptions for instructions on how to modify the
default values. Options include port disable and non-removable pin strapping.
8.5
Default Strapping Options
The USB251x can be configured via a combination of internal default values and pin strap options.
Please see Table 8.2 for specific details on how to enable the default/pin-strap configuration option.
The strapping option pins only cover a limited sub-set of the configuration options. The internal default
values will be used for the bits & registers that are not controlled by a strapping option pin. Please
refer to Table 8.2 for the internal default values that are loaded when this option is selected.
8.6
Strap Options
Table 8.7 Summary of Strap Options
8.6.1
Non-Removable Strap Option
The strap function of the NON_REM[x:0] pins are enabled through the internal default configuration.
The driver type of each strap pin is I/O (no internal pull-up or pull-down for the input function). Use
this type of strap option for NON_REM[1:0]. Figure 8.3 shows an example of Strap High and Strap
Low. Use the Strap High configuration to set the strap option value to a ‘1’. Use the Strap Low
configuration to set the strap option value to ‘0’.
Part
Number
USB251x
USB251xi
USB251xA
USB251xAi
USB251xB
USB251xBi
Resistor Value
(R)
Notes
Normal
47 - 100 k
Ω
Internal Pull-Down
10 k
Ω
Only applicable to port power pins.
Contains a built-in resistor.
LED
47 - 100 k
Ω
相關PDF資料
PDF描述
UM-5-FREQ-STBY1-TOL1-AGE3-SR-DL2 QUARTZ CRYSTAL RESONATOR, 10 MHz - 30 MHz
UM-5-FREQ-STBY1-TOL2-AGE2-SR-DL1 QUARTZ CRYSTAL RESONATOR, 10 MHz - 30 MHz
UM-5-FREQ-7OT-STBY3-TOL4-AGE3-CL1-DL2 QUARTZ CRYSTAL RESONATOR, 150 MHz - 200 MHz
UM-1-FREQ-STBY2-TOL1-AGE3-SR-DL4 QUARTZ CRYSTAL RESONATOR, 10 MHz - 30 MHz
UM-1-FREQ-STBY2-TOL4-AGE1-SR-DL4 QUARTZ CRYSTAL RESONATOR, 10 MHz - 30 MHz
相關代理商/技術參數
參數描述
USB2513-AEZG-TR 功能描述:USB 接口集成電路 HI-PERFORM LW PWR SM FOOT USB 2.0 HUB RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
USB2513B 制造商:SMSC 制造商全稱:SMSC 功能描述:USB 2.0 Hi-Speed Hub Controller
USB2513B-AEZC 功能描述:IC LINEAR RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:* 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN(6x6) 包裝:* 其它名稱:Q6396337A
USB2513B-AEZC-TR 制造商:Microchip Technology 功能描述:USB 2.0 HIGH SPEED 3 PORT HUB 制造商:Microchip Technology 功能描述:USB 2.0 Hub Controller 36-Pin QFN EP T/R 制造商:Microchip Technology Inc 功能描述:MCCUSB2513B-AEZC-TR USB CHIP 制造商:Microchip Technology Inc 功能描述:3-PORT USB 2.0 HI-SPEED HUB CONTROLLER - Tape and Reel 制造商:Microchip Technology Inc 功能描述:3-PORT USB 2.0 HUB CTRLR 36VQFN 制造商:Microchip Technology Inc 功能描述:USB 2.0 HIGH SPEED 3 PORT HUB CNTLR
USB2513B-AEZG 功能描述:USB 接口集成電路 USB2.0 HIGH SPEED 3-Port Hub ControllR RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20