參數資料
型號： USB2513-AEZG
廠商： STANDARD MICROSYSTEMS CORP
元件分類： 總線控制器
中文描述： UNIVERSAL SERIAL BUS CONTROLLER, QCC36
封裝： 6 X 6 MM, 0.50 MM PITCH, ROHS COMPLIANT, QFN-36
文件頁數： 48/76頁
文件大?。?/td> 1924K
代理商： USB2513-AEZG
USB 2.0 Hi-Speed Hub Controller
Datasheet
Revision 1.1 (04-26-10)
52
SMSC USB251x
DATASHEET
8.2.1.35
Register FFh: Status/Command
8.2.2
I2C EEPROM
The I2C EEPROM interface implements a subset of the I2C Master specification (Please refer to the
Philips Semiconductor Standard I2C-Bus specification for details on I2C bus protocols). The SMSC
hub’s I2C EEPROM interface is designed to attach to a single “dedicated” I2C EEPROM, and it
conforms to the Standard-mode I2C specification (100 kbit/s transfer rate and 7-bit addressing) for
protocol and electrical compatibility.
Note: Extensions to the I2C specification are not supported.
The hub acts as the master and generates the serial clock SCL, controls the bus access (determines
which device acts as the transmitter and which device acts as the receiver), and generates the START
and STOP conditions.
8.2.2.1
Implementation Characteristics
The hub will only access an EEPROM using the sequential read protocol.
8.2.2.2
Pull-Up Resistor
The circuit board designer is required to place external pull-up resistors (10 k
Ω recommended) on the
SDA / SMBDATA and SCL / SMBCLK / CFG_SEL[0] lines (per SMBus 1.0 specification, and EEPROM
manufacturer guidelines) to VDD33 in order to assure proper operation.
8.2.2.3
I2C EEPROM Slave Address
The slave address is 1010000.
Note: 10-bit addressing is NOT supported.
8.2.3
In-Circuit EEPROM Programming
The EEPROM can be programmed via ATE (automatic test equipment) by pulling RESET_N low
(which tri-states the hub’s EEPROM interface and allows an external source to program the EEPROM).
BIT
NUMBER
BIT NAME
DESCRIPTION
7:3
Reserved
2
INTF_PW_DN
SMBus Interface Power Down
‘0’ = Interface is active
‘1’ = Interface power down after ACK has completed
1
RESET
Reset the SMBus Interface and internal memory back to RESET_N
assertion default settings.
‘0’ = Normal Run/Idle State
‘1’ = Force a reset of registers to their default state
0
USB_ATTACH
USB Attach (and write protect)
‘0’ = SMBus slave interface is active
‘1’ = The hub will signal a USB attach event to an upstream device, and the
internal memory (address range 00h-FEh) is “write-protected” to prevent
unintentional data corruption.
相關PDF資料
PDF描述
UM-5-FREQ-STBY1-TOL1-AGE3-SR-DL2 QUARTZ CRYSTAL RESONATOR, 10 MHz - 30 MHz
UM-5-FREQ-STBY1-TOL2-AGE2-SR-DL1 QUARTZ CRYSTAL RESONATOR, 10 MHz - 30 MHz
UM-5-FREQ-7OT-STBY3-TOL4-AGE3-CL1-DL2 QUARTZ CRYSTAL RESONATOR, 150 MHz - 200 MHz
UM-1-FREQ-STBY2-TOL1-AGE3-SR-DL4 QUARTZ CRYSTAL RESONATOR, 10 MHz - 30 MHz
UM-1-FREQ-STBY2-TOL4-AGE1-SR-DL4 QUARTZ CRYSTAL RESONATOR, 10 MHz - 30 MHz
相關代理商/技術參數
參數描述
USB2513-AEZG-TR 功能描述:USB 接口集成電路 HI-PERFORM LW PWR SM FOOT USB 2.0 HUB RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
USB2513B 制造商:SMSC 制造商全稱:SMSC 功能描述:USB 2.0 Hi-Speed Hub Controller
USB2513B-AEZC 功能描述:IC LINEAR RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:* 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN（6x6） 包裝:* 其它名稱:Q6396337A
USB2513B-AEZC-TR 制造商:Microchip Technology 功能描述:USB 2.0 HIGH SPEED 3 PORT HUB 制造商:Microchip Technology 功能描述:USB 2.0 Hub Controller 36-Pin QFN EP T/R 制造商:Microchip Technology Inc 功能描述:MCCUSB2513B-AEZC-TR USB CHIP 制造商:Microchip Technology Inc 功能描述:3-PORT USB 2.0 HI-SPEED HUB CONTROLLER - Tape and Reel 制造商:Microchip Technology Inc 功能描述:3-PORT USB 2.0 HUB CTRLR 36VQFN 制造商:Microchip Technology Inc 功能描述:USB 2.0 HIGH SPEED 3 PORT HUB CNTLR
USB2513B-AEZG 功能描述:USB 接口集成電路 USB2.0 HIGH SPEED 3-Port Hub ControllR RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*