- 您現在的位置：買賣IC網 > PDF目錄366059 > TZA3031AHL (NXP SEMICONDUCTORS) SDH/SONET STM1/OC3 laser drivers(SDH/SONET STM1/OC3 激光驅動器) PDF資料下載
參數資料
| 型號： | TZA3031AHL |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 其它接口 |
| 英文描述： | SDH/SONET STM1/OC3 laser drivers(SDH/SONET STM1/OC3 激光驅動器) |
| 中文描述： | SPECIALTY INTERFACE CIRCUIT, PQFP32 |
| 封裝： | 5 X 5 X 1.40 MM, PLASTIC, LQFP-32 |
| 文件頁數： | 9/32頁 |
| 文件大?。?/td> | 137K |
| 代理商： | TZA3031AHL |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
2000 Feb 22
9
Philips Semiconductors
Product specification
SDH/SONET STM1/OC3 laser drivers
TZA3031AHL; TZA3031BHL;
TZA3031U
In this example, the resulting bandwidth for the optical 1
modulation current control loop, without an external
capacitor, is:
10
×
500
×
×
2
π
40
×
10
×
80
×
The resulting bandwidth for the optical 0 bias current
control loop, without an external capacitor, is:
30
×
10
×
×
2
π
40
×
10
×
It is not necessary to add additional capacitance with this
type of laser.
Control loop data pattern and bit rate dependency
The constants in equations (1) and (3) are valid when the
data pattern frequently contains a sufficient number of
‘constantzeroes’and‘constantones’.Asinglecontrolloop
time period (
τ
ONE
and
τ
ZERO
) must contain ones and zeros
for at least approximately 6 ns. In practice, the optical
extinction ratio increases if the bit rate increases.
Therefore, it is important to use the actual data patterns
and bit rate of the final application circuit for adjusting the
optical levels.
The laser driver peak detectors are able to track MPD
output current overshoot and undershoot conditions.
Unfortunately, these conditions affect the ability of the IC
to correctly interpret the high and low level MPD current.
In particular, the occurrence of undershoot can have a
markedly adverse effect on the interpretation of the low
level MPD current.
Additional bias by modulation ‘off’ current
Although during operation, the full modulation current
switches between outputs LA and LAQ, a small amount of
modulation current continues to flow through the inactive
pin.
For example, when the laser, whose cathode is connected
to LA, is in the ‘dark’ part of its operating cycle (logic 0),
some of the modulation ‘off’ current flows through LA while
most of the current flows through LAQ. This value
I
o(mod)(off)
is effectively added to the bias current and is
subtracted from the modulation current. Fortunately, the
value correlates closely with the magnitude of the
modulation current. Therefore, applications requiring low
bias and low modulation are less affected. Figure 9 shows
the modulation ‘off’ current as a function of the modulation
‘on’ current.
Monitoring the bias and modulation current
Although not recommended, the bias and modulation
currents generated by the laser driver can be monitored by
measuring the voltages on pins TZERO and TONE,
respectively (see Fig.10). The relationship between these
voltages and the corresponding currents are given as
transconductance values and are specified in
Chapter “Characteristics”. The voltages on pins TZERO
and TONE range from 1.4 to 3.4 V. Any connection to
these pins should have a very high impedance value. It is
mandatory to use a CMOS buffer or an amplifier with an
input impedance higher than 100 G
and with an
extremely low input leakage current (pA).
B
ONE
3
–
10
×
3
–
12
–
10
3
----30
750 Hz
≈
=
B
ZERO
3
–
500
50
×
10
10
3
3
–
×
×
12
–
0.5
600 Hz
≈
=
handbook, halfpage
0
20
40
60
1
0
2
MGS902
Io(mod)(on) (mA)
(2)
(1)
Io(mod)(off)
(mA)
Fig.9 I
o(mod)(off)
as a function of I
o(mod)(on)
.
(1) Worst case operation (T
= 125
°
C, V
CC
= 5.5 V
and worst case parameter processes).
(2) Typical operation.
相關PDF資料 |
PDF描述 |
|---|---|
| TZA3034T | SDH/SONET STM1/OC3 postamplifiers |
| TZA3034 | SDH/SONET STM1/OC3 postamplifier |
| TZA3034TT | SDH/SONET STM1/OC3 postamplifier |
| TZA3034U | SDH/SONET STM1/OC3 postamplifier |
| TZA3041AHL | Gigabit Ethernet/Fibre Channel laser drivers(千兆位以太網/光纖通道激光驅動器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TZA3031BHL | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:SDH/SONET STM1/OC3 laser drivers |
| TZA3031U | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:SDH/SONET STM1/OC3 laser drivers |
| TZA3033 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:SDH/SONET STM1/OC3 and STM4/OC12 transceiver |
| TZA3033T | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:SDH/SONET STM1/OC3 transimpedance amplifier |
| TZA3033U | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:SDH/SONET STM1/OC3 transimpedance amplifier |
發布緊急采購，3分鐘左右您將得到回復。