參數資料
型號： TZA3031AHL
廠商： NXP SEMICONDUCTORS
元件分類： 其它接口
英文描述： SDH/SONET STM1/OC3 laser drivers(SDH/SONET STM1/OC3 激光驅動器)
中文描述： SPECIALTY INTERFACE CIRCUIT, PQFP32
封裝： 5 X 5 X 1.40 MM, PLASTIC, LQFP-32
文件頁數： 13/32頁
文件大小： 137K
代理商： TZA3031AHL
2000 Feb 22
13
Philips Semiconductors
Product specification
SDH/SONET STM1/OC3 laser drivers
TZA3031AHL; TZA3031BHL;
TZA3031U
Bias alarm for TZA3031AHL
The bias current alarm circuit detects whenever the bias
current is outside a predefined range, and generates a
flag. This feature can detect excessive bias current due to
laser ageing or laser malfunctioning. The current applied
to pin ALARMHI should be the maximum permitted bias
current value attenuated by a ratio of 1:1500. The current
applied to pin ALARMLO should be the minimum
permitted bias current value attenuated by a ratio of 1:300.
Like the reference currents for the laser current control
loop, the alarm reference currents can be set by
connecting external resistors between V
CC(R)
and
pins ALARMHI and ALARMLO (see Fig.8). The resistor
values can be calculated using the following formulae:
1500
×
O BIAS
)
max
(
)
(9)
(10)
Example:
The following reference currents are required to
limit the bias current range from 6 to 90 mA:
and
The corresponding resistor values are:
1500
×
90
10
×
300
×
6
10
×
and
If the alarm condition is true, the voltage on pin ALARM
(see Fig.14) goes to a HIGH level (CMOS). This signal
could be used, for example, to drive pin ALS to disable the
laser driver; the signal to pin ALS has to be latched to
prevent oscillation.
A hysteresis of approximately 10% is applied to both alarm
functions. The attenuation ratios of 1:300 and 1:1500 are
valid if the bias current rises above the reference current
levels. If the bias current decreases, the ratios are 10%
lower.
Accuracy of voltage on inputs: ONE, ZERO,
ALARMLO, ALARMHI
It is important to consider the accuracy of the 1.5 V level
with respect to V
CC(R)
on pins ONE and ZERO if resistors
are used to set the reference currents. Although this value
is independent of V
CC(R)
, deviations from 1.5 V can be
caused by:
Input current: At T
j
= 25
°
C, the voltage between pin and
V
CC
varies from 1.58 V at an input current of 6
μ
A, down
to 1.45 V at 65
μ
A and 1.41 V at 100
μ
A. The range
between 65
μ
A and 100
μ
A is only specified for
ALARMLO. In the application, the input current is
virtually fixed, so this variation has little effect.
Variation in batch and individual device characteristics,
not exceeding
±
2% from the nominal product: This
variation can be compensated for where devices in the
application are individually trimmed.
Temperature: The variation in T
j
is shown in Fig.15.
At 30
μ
A (middle of the specified range) the total
variation in T
j
is <1%, at 65
μ
A it is <2% and at 6
μ
A it is
<3%.
R
ALARMHI
I
=
[
]
R
ALARMLO
I
O BIAS
300
×
)
min
(
)
----1.5
=
[
]
I
ALARMLO
6
10
3
–
×
300
20
μ
A
=
=
I
ALARMHI
90
10
3
–
×
1500
60
μ
A
=
=
R
ALARMHI
3
–
1.5
25 k
=
=
R
ALARMLO
3
–
1.5
75 k
=
=
handbook, halfpage
MGS909
20
43
VCC(R)
GND
ALARM
Fig.14 ALARM output.
相關PDF資料
PDF描述
TZA3034T SDH/SONET STM1/OC3 postamplifiers
TZA3034 SDH/SONET STM1/OC3 postamplifier
TZA3034TT SDH/SONET STM1/OC3 postamplifier
TZA3034U SDH/SONET STM1/OC3 postamplifier
TZA3041AHL Gigabit Ethernet/Fibre Channel laser drivers(千兆位以太網/光纖通道激光驅動器)
相關代理商/技術參數
參數描述
TZA3031BHL 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:SDH/SONET STM1/OC3 laser drivers
TZA3031U 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:SDH/SONET STM1/OC3 laser drivers
TZA3033 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:SDH/SONET STM1/OC3 and STM4/OC12 transceiver
TZA3033T 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:SDH/SONET STM1/OC3 transimpedance amplifier
TZA3033U 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:SDH/SONET STM1/OC3 transimpedance amplifier
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*