- 您現在的位置：買賣IC網 > PDF目錄371189 > TZA3004HL (NXP SEMICONDUCTORS) SDH/SONET data and clock recovery unit STM1/4 OC3/12 PDF資料下載
參數資料
| 型號： | TZA3004HL |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 數字傳輸電路 |
| 英文描述： | SDH/SONET data and clock recovery unit STM1/4 OC3/12 |
| 中文描述： | CLOCK RECOVERY CIRCUIT, PQFP48 |
| 封裝： | 7 X 7 MM, 1.40 MM HEIGHT, PLASTIC, MS-026, SOT-313-2, LQFP-48 |
| 文件頁數： | 11/28頁 |
| 文件大?。?/td> | 127K |
| 代理商： | TZA3004HL |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
2000 Feb 17
11
Philips Semiconductors
Product specification
SDH/SONET STM1/OC3 and STM4/OC12
transceiver
TZA3005H
Other operating modes
D
IAGNOSTIC LOOPBACK
A transmitter-to-receiver loopback mode is available for
diagnostic purposes. When DLEN is LOW, the differential
serial clock and data from the transmitter parallel-to-serial
block continue to be routed to transmitter outputs, but are
also routed to the receiver serial-to-parallel block instead
of the receiver input signals from pins RXSD/RXSDQ and
RXSCLK/RXSCLKQ.
L
INE LOOPBACK
A receiver-to-transmitter loopback mode is available for
line testing purposes. When LLEN is LOW, the receiver
input signals (RXSD/RXSDQ and RXSCLK/RXSCLKQ)
are routed, after retiming, to the transmitter output buffers.
The receiver clock and data are also routed to the
serial-to-parallel block.
L
OOP TIMING
In loop timing mode, the transmitter section is clocked by
the receiver input clock (RXSCLK) instead of by the
internal clock synthesizer. SYNCLKDIV is now derived
from RXSCLK so that it can be used to clock upstream
transmitter logic. Loop timing is enabled by setting pins
ALTPIN, TEST1, TEST2 and TEST3 (see Table 6). After
activating the loop timing mode, the receiver clock must be
synchronized to the transmitter input data
(TXPD0 to TXPD7) by activating master reset (MRST).
In loop timing mode, the internal clock synthesizer is still
used to generate the 19MHz output clock signal on
pin 19MHZO.
S
QUELCHED CLOCK OPERATION
Some clock recovery devices force their recovered output
clock to zero if a loss of input signal is detected. If this
happens, the SDTTL or SDPECL signals are inactive and
no clock signal is present at pins RXSCLK and RXSCLKQ.
If no clock signal is present at pins RXSCLK/RXSCLKQ,
there is no RXPCLK signal. This may not be suitable for
some applications, in which case, the TZA3005H can be
set to squelched clock operation by setting pins ALTPIN,
TEST1, TEST2 and TEST3 as shown in Table 6.
In squelched clock operation, receiver timing is performed
by a part of the internal clock synthesizer which normally
only provides transmitter timing. This produces a RXPCLK
clock signal when either SDTTL or SDPECL is inactive. If
either SDTTL or SDPECL is inactive in squelched clock
operation, it is equivalent to normal operation. During a
transition from normal operation to squelched clock
operation, the RXPCLK clock cycle exhibits a once-only
random shortening.
Table 6 shows that the same operating mode can be
selected at different settings of the control inputs.
If ALTPIN = 0, the STM4 nibble mode is not available, but
is used for squelched clock operation. If ALTPIN = 1, all
operating modes are available, including STM4 nibble
mode.
相關PDF資料 |
PDF描述 |
|---|---|
| X00602 | SENSITIVE GATE SCR |
| X00602MA | 0.8A SCRs |
| X00602MA1AA2 | 0.8A SCRs |
| X00602MA2AL2 | 0.8A SCRs |
| X00602MA5AL2 | 0.8A SCRs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TZA3005 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:SDH/SONET STM1/OC3 and STM4/OC12 transceiver |
| TZA3005H | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:SDH/SONET STM1/OC3 and STM4/OC12 transceiver |
| TZA3011A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:30 Mbits/s up to 3.2 Gbits/s A-rate(TM) laser drivers |
| TZA3011AVH/C2,551 | 功能描述:激光驅動器 3.3V D-LOOP LASERDRVR DC-3.2GB RoHS:否 制造商:Micrel 數據速率:4.25 Gbps 工作電源電壓:3 V to 3.6 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-16 封裝:Tube |
| TZA3011AVH/C2,557 | 功能描述:激光驅動器 3.3V D-LOOP LASERDRVR DC-3.2GB RoHS:否 制造商:Micrel 數據速率:4.25 Gbps 工作電源電壓:3 V to 3.6 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-16 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。