參數資料
型號： TVP3026-135
廠商： Texas Instruments, Inc.
英文描述： Video Interface PALETTE Exract(組合像素模式視頻接口調色器)
中文描述： 視頻接口調色板Exract（組合像素模式視頻接口調色器）
文件頁數： 53/107頁
文件大?。?/td> 707K
代理商： TVP3026-135
2–39
2.11.4
Silicon Revision
The silicon revision register (index: 0x01) is a read-only register that enables software to identify the silicon
revision of the TVP3026. On the first pass silicon, this register reads back 0x00. A major revision number
is stored in bits 7–4 and a minor revision number is stored in bits 3–0.
2.12 General-Purpose I/O Register and Terminals
The general-purpose I/O register and output terminals provide a means of controlling external functions
through the TVP3026 microinterface. The 8-bit general-purpose I/O data register has five bit locations
(D0–D4) tied to external I/O terminals (GI/O0–GI/O4). The other three bits (D5–D7) can be used for
general data storage and do not affect any other circuitry. The general-purpose I/O data register is controlled
by the general-purpose I/O control register. GP I/O control register bits IOC0–IOC4 control whether the
corresponding general-purpose I/O terminals are configured as inputs or outputs. The reset default
condition is for GP I/O control register bits IOC0–IOC4 = 0, which configures terminals GI/O0–GI/O4 as
inputs. When any of the GP I/O control register bits are set to 1, the corresponding GI/O terminals are
configured as outputs.
The general-purpose I/O control register, data register, and terminal relationships are shown in Table 2–25.
Table 2–25. General Purpose I/O Registers
DATA BIT
D7
D6
D5
D4
D3
D2
D1
D0
General-Purpose I/O Control Register
Index: 0x2A
Access: R/W
Default: 0x00
X
X
X
IOC4
IOC3
IOC2
IOC1
IOC0
General-Purpose I/O Data Register
Index: 0x2B
Access: R/W
Default: Uninitialized
X
X
X
D4
D3
D2
D1
D0
General-Purpose I/O Terminal Locations
X = do not care
GI/O4
GI/O3
GI/O2
GI/O1
GI/O0
2.13 Reset
There are two ways to reset the TVP3026. The RESET input terminal can perform a hardware reset.
Alternatively, the device has an integrated software reset function.
A hardware reset is initiated by pulling the RESET input terminal low. When RESET is pulled low all
TVP3026 registers go to default states. This reset is asynchronous, and any glitch on this terminal could
change the intended register setup. The default state at reset is VGA mode, and all default register settings
are given in Table 2–2. When a reset is desired at power up, an external resistor, capacitor, and diode
network can be connected to the RESET terminal. When TTL logic is employed to provide the signal to the
RESET terminal, a pullup resistor should be used to make sure that CMOS levels are achieved.
For a software reset, anytime the reset register (index: 0xFF) is written to, all registers are initialized to
TVP3026 default settings. The data written into the reset register is ignored.
2.14 Analog Output Specifications
The DAC outputs are controlled by three current sources (only two for IOR and IOB) as shown in
Figure 2–12. The default condition is to have 0 IRE difference between blank and black levels, which is
shown in Figure 2–13. When a 7.5-IRE (Institute of Radio Engineers, predecessor to the IEEE) pedestal
is desired, it can be selected by setting bit 4 of the general-control register. This video output is shown in
Figure 2–14.
相關PDF資料
PDF描述
TVP3026-175 Video Interface PALETTE Exract(組合像素模式視頻接口調色器)
TVP3026-175M Video Interface PALETTE Exract(組合像素模式視頻接口調色器)
TVP3026-220 Video Interface PALETTE Exract(組合像素模式視頻接口調色器)
TVP3026-250 Video Interface PALETTE Exract(組合像素模式視頻接口調色器)
TX24 60.8 MM 5 X 8 DOT MATRIX DISPLAYS
相關代理商/技術參數
參數描述
TVP3026-135AMDN 制造商:TI 制造商全稱:Texas Instruments 功能描述:Video Interface Palette
TVP3026-135APCE 制造商:TI 制造商全稱:Texas Instruments 功能描述:Video Interface Palette
TVP3026-135BMDN 制造商:TI 制造商全稱:Texas Instruments 功能描述:Video Interface Palette
TVP3026-135BPCE 制造商:TI 制造商全稱:Texas Instruments 功能描述:Video Interface Palette
TVP3026-135MDN 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Video DAC with Color Palette (RAMDAC)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*