參數資料
型號: TPS61130RSAR
廠商: TEXAS INSTRUMENTS INC
元件分類: 穩壓器
英文描述: 1.6 A BATTERY CHARGE CONTROLLER, 600 kHz SWITCHING FREQ-MAX, PQCC16
封裝: 4 X 4 MM, PLASTIC, QFN-16
文件頁數: 8/30頁
文件大?。?/td> 812K
代理商: TPS61130RSAR
www.ti.com
APPLICATION INFORMATION
DESIGN PROCEDURE
Programming the Output Voltage
DC/DC Converter
R3 + R6
V
O
V
FB
* 1 + 180 kW
V
O
500 mV *
1
(1)
C
parR3 +
20 pF
200 kW
R6
* 1
(2)
SWN
C3
10 F
Power
Supply
R1
R2
VBAT
VOUT
FB
R3
R6
LDOIN
R5
R4
LDOSENSE
LDOOUT
R7
R9
C6
2.2 F
C4
100 F
U1
LBO
PGOOD
PGND
LBI
SKIPEN
EN
LDOEN
GND
TPS6113xPW
VCC1
SEPICOutput
VCC2
LDOOutput
Control
Outputs
C5
2.2 F
L1A
22 H
SWP
C7
L1B
22 H
10 F
SLVS431B – JUNE 2002 – REVISED JANUARY 2008
The TPS6113x dc/dc converters are intended for systems powered by a dual up to 4 cell NiCd or NiMH battery
with a typical terminal voltage between 1.8 V and 6.5 V. They can also be used in systems powered by one-cell
Li-Ion with a typical stack voltage between 2.5 V and 4.2 V. Additionally, two up to four primary alkaline battery
cells can be the power source in systems where the TPS6113x is used.
The output voltage of the TPS61130 dc/dc converter section can be adjusted with an external resistor divider.
The typical value of the voltage on the FB pin is 500 mV. The maximum recommended value for the output
voltage is 5.5 V. The current through the resistive divider should be about 100 times greater than the current into
the FB pin. The typical current into the FB pin is 0.01
A and the voltage across R6 is typically 500 mV. Based
on those two values, the recommended value for R6 should be lower than 500 k
, in order to set the divider
current at 1
A or higher. Because of internal compensation circuitry the value for this resistor should be in the
range of 200 k
. From that, the value of resistor R3, depending on the needed output voltage (VO), can be
calculated using Equation 1:
If as an example, an output voltage of 3.3 V is needed, a 1-M
resistor should be chosen for R3. If for any
reason the value for R6 is chosen significantly lower than 200 k
additional capacitance in parallel to R3 is
recommended. The required capacitance value can be easily calculated using Equation 2.
Figure 24. Typical Application Circuit for Adjustable Output Voltage Option
16
Copyright 2002–2008, Texas Instruments Incorporated
Product Folder Link(s): TPS61130 TPS61131 TPS61132
相關PDF資料
PDF描述
TPS2421-2DDA 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8
TS5A3160DCKR 1-CHANNEL, SGL POLE DOUBLE THROW SWITCH, PDSO6
TS3809CXBRF 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO3
TC05AMRM 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 2.5 V, MBCY2
TC151B2919EOA723 0.25 A SWITCHING REGULATOR, 50 kHz SWITCHING FREQ-MAX, PDSO8
相關代理商/技術參數
參數描述
TPS61130RSARG4 功能描述:直流/直流開關調節器 Adj 90% Eff SEPIC Converter RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5
TPS61131 制造商:TI 制造商全稱:Texas Instruments 功能描述:SYNCHRONOUS SEPIC / FLYBACK CONVERTER WITH 1.1A SWITCH AND INTEGRATED LDO
TPS61131PW 功能描述:直流/直流開關調節器 3.3V 90% Eff SEPIC Converter RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5
TPS61131PW 制造商:Texas Instruments 功能描述:IC SEPIC CONV DUAL CELL 16-TSSOP 制造商:Texas Instruments 功能描述:IC, SEPIC CONV DUAL CELL 16-TSSOP 制造商:Texas Instruments 功能描述:IC, SEPIC CONV DUAL CELL 16-TSSOP; Primary Input Voltage:6.5V; No. of Outputs:2; Output Voltage:3.3V; Output Current:300mA; Voltage Regulator Case Style:TSSOP; No. of Pins:16; Operating Temperature Min:-40C; Operating Temperature ;RoHS Compliant: Yes
TPS61131PWG4 功能描述:直流/直流開關調節器 3.3V 90% Eff SEPIC Converter RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5