- 您現在的位置：買賣IC網 > PDF目錄103067 > TPS61045DRBT (TEXAS INSTRUMENTS INC) 0.45 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO8 PDF資料下載
參數資料
| 型號： | TPS61045DRBT |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | 0.45 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO8 |
| 封裝： | 3 X 3 MM, GREEN, PLASTIC, SON-8 |
| 文件頁數： | 2/21頁 |
| 文件大?。?/td> | 582K |
| 代理商： | TPS61045DRBT |
(
)
IN
O
IN
s(max)
P
O
V
f
=
I
L V
-
375
100
IN
P(typ)
V
I
=
m A
ns
L
+
(
)
2
LOAD
O
IN
F
S(ILOAD)
P
I
V
f
=
I
L
-
+
375
100
IN
P(typ)
V
I
m A
ns
L
=
+
t
P
fall
O
IN
I
L
V
=
-
SLVS440B – JANUARY 2003 – REVISED MARCH 2009
www.ti.com
APPLICATION INFORMATION
INDUCTOR SELECTION, MAXIMUM LOAD CURRENT
Since the PFM peak current control scheme is inherently stable the inductor and capacitor value does not affect
the stability of the regulator. The selection of the inductor together with the nominal load current, input, and
output voltage of the application determines the switching frequency of the converter. Depending on the
application, inductor values between 2.2 mH up to 47 mH are recommended. The maximum inductor value is
determined by the maximum switch on-time of 6 ms (typ). The peak current limit of 375 mA (typ) must be reached
within this 6 ms for proper operation.
The inductor value determines the maximum switching frequency of the converter. Therefore, the inductor value
must be selected for the maximum switching frequency, at maximum load current of the converter and should not
be exceeded. A good inductor value to start with is 4.7 mH. The maximum switching frequency is calculated as:
with:
IP = peak current as described in the previous peak current control section.
L = selected inductor value; per the above description inductor values between 2.2 mH up to 47 mH are
recommended.
If the selected inductor does not exceed the maximum switching frequency of the converter, as a next step, the
switching frequency at the nominal load current is estimated as follows:
with:
IP = peak current as described in the previous chapter peak current control section
L = selected inductor value
I(LOAD) = nominal load current
VF = rectifier diode forward voltage (typically 0.3 V)
The smaller the inductor value, the higher the switching frequency of the converter but the lower the efficiency.
The maximum load current of the converter is determined at the operation point where the converter starts to
enter continuous conduction mode. The converter must always operate in discontinuous conduction mode to
maintain regulation.
Two conditions exist for determining the maximum output current of the converter. One is when the inductor
current fall time is <400 ns, and the other is when the inductor current fall time is >400 ns.
One way to calculate the maximum available load current under certain operation conditions is to estimate the
expected converter efficiency at the maximum load current. This number can be taken out of the efficiency
Inductor fall time:
For tf ≥ 400 ns
10
Copyright 2003–2009, Texas Instruments Incorporated
Product Folder Link(s): TPS61045
相關PDF資料 |
PDF描述 |
|---|---|
| TC647BEOATR | BRUSHLESS DC MOTOR CONTROLLER, PDSO8 |
| TPS65131RGER | 2.2 A SWITCHING REGULATOR, 1500 kHz SWITCHING FREQ-MAX, PQCC24 |
| TPS65014RGZ | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC48 |
| TLVH431BIDBZTG4 | 1-OUTPUT THREE TERM VOLTAGE REFERENCE, 1.24 V, PDSO3 |
| TPS3707-33DGNRG4 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS61045DRBTG4 | 功能描述:LED照明驅動器 28-V 85% Eff Boost Converter RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| TPS61045EVM-231 | 功能描述:電源管理IC開發工具 TPS61045-231 Eval Mod RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| TPS61046EVM-682 | 功能描述:TPS61046 - DC/DC, Step Up 2, Non-Isolated Outputs Evaluation Board 制造商:texas instruments 系列:- 零件狀態:有效 主要用途:DC/DC，步升 輸出和類型:2，非隔離 功率 - 輸出:- 電壓 - 輸出:12V，5 V ~ 28 V 電流 - 輸出:100mA，20mA 電壓 - 輸入:1.8 V ~ 5.5 V 穩壓器拓撲:升壓 頻率 - 開關:1MHz 板類型:完全填充 所含物品:板 使用的 IC/零件:TPS61046 標準包裝:1 |
| TPS61046YFFR | 功能描述:LED 驅動器 IC 1 輸出 DC DC 穩壓器 升壓（升壓） 調光 1.2A（開關） 6-DSBGA 制造商:texas instruments 系列:- 包裝:剪切帶（CT） 零件狀態:新產品 類型:DC DC 穩壓器 拓撲:升壓（升壓） 內部開關:是 輸出數:1 電壓 - 供電（最低）:1.8V 電壓 -?供電（最高）:5.5V 電壓 - 輸出:4.5 V ~ 28 V 電流 - 輸出/通道:1.2A（開關） 頻率:1.05MHz 調光:- 應用:- 工作溫度:-40°C ~ 125°C （TJ） 安裝類型:表面貼裝 封裝/外殼:6-UFBGA，DSBGA 供應商器件封裝:6-DSBGA 標準包裝:1 |
| TPS61046YFFT | 功能描述:LED 驅動器 IC 1 輸出 DC DC 穩壓器 升壓（升壓） 1.2A（開關） 6-DSBGA 制造商:texas instruments 系列:- 包裝:剪切帶（CT） 零件狀態:有效 類型:DC DC 穩壓器 拓撲:升壓（升壓） 內部開關:是 輸出數:1 電壓 - 供電（最低）:1.8V 電壓 -?供電（最高）:5.5V 電壓 - 輸出:4.5 V ~ 28 V 電流 - 輸出/通道:1.2A（開關） 頻率:1.05MHz 調光:- 應用:- 工作溫度:-40°C ~ 125°C （TJ） 安裝類型:表面貼裝 封裝/外殼:6-UFBGA，DSBGA 供應商器件封裝:6-DSBGA 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。