![](http://datasheet.mmic.net.cn/370000/TPS61026DRC_datasheet_16739783/TPS61026DRC_1.png)
(3,25 mm x 3,25 mm)
www.ti.com
FEATURES
96% Efficient Synchronous Boost Converter
Output Voltage Remains Regulated When
Input Voltage Exceeds Nominal Output
Voltage
Device Quiescent Current: 25 μA (Typ)
Input Voltage Range: 0.9 V to 6.5 V
Fixed and Adjustable Output Voltage Options
Up to 5.5 V
Power Save Mode for Improved Efficiency at
Low Output Power
Low Battery Comparator
Low EMI-Converter (Integrated Antiringing
Switch)
Load Disconnect During Shutdown
Over-Temperature Protection
Small 3 mm
×
3 mm QFN-10 Package
DESCRIPTION
The TPS6102x devices provide a power supply
solution for products powered by either a one-cell,
two-cell, or three-cell alkaline, NiCd or NiMH, or
one-cell Li-Ion or Li-polymer battery. Output currents
can go as high as 200 mA while using a single-cell
alkaline, and discharge it down to 0.9 V. It can also
be used for generating 5 V at 500 mA from a 3.3-V
rail or a Li-Ion battery. The boost converter is based
on a fixed frequency, pulse-width-modulation (PWM)
controller using a synchronous rectifier to obtain
maximum
efficiency.
At
converter enters the Power Save mode to maintain a
high efficiency over a wide load current range. The
Power Save mode can be disabled, forcing the
converter to operate at a fixed switching frequency.
The maximum peak current in the boost switch is
limited to a value of 800 mA, 1500 mA or 1800mA
depending on the device version.
APPLICATIONS
All One-Cell, Two-Cell and Three-Cell Alkaline,
NiCd or NiMH or Single-Cell Li Battery
Powered Products
Portable Audio Players
PDAs
Cellular Phones
Personal Medical Products
Camera White LED Flash Light
SW
C1
10
μ
F
L1
6.8
μ
H
R1
R2
VBAT
VOUT
FB
C2
2.2
μ
F
C3
47
μ
F
LBO
PGND
LBI
PS
EN
GND
TPS61020
V
O
3.3 V Up To
200 mA
Low Battery
Output
R3
R4
R5
0.9-V To
6.5-V Input
TPS61020
,
TPS61024
,
TPS61025
TPS61026, TPS61027, TPS61028
TPS61029
SLVS451D–SEPTEMBER 2003–REVISED FEBRUARY 2006
96% EFFICIENT SYNCHRONOUS BOOST CONVERTER
low
load
currents
the
The TPS6102x devices keep the output voltage
regulated even when the input voltage exceeds the
nominal output voltage. The output voltage can be
programmed by an external resistor divider, or is
fixed internally on the chip. The converter can be
disabled to minimize battery drain. During shutdown,
the load is completely disconnected from the battery.
A low-EMI mode is implemented to reduce ringing
and, in effect, lower radiated electromagnetic energy
when
the
converter
enters
conduction mode. The device is packaged in a
10-pin QFN PowerPAD package measuring 3 mm
x 3 mm (DRC).
the
discontinuous
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PowerPAD is a trademark of Texas Instruments.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright 2003–2006, Texas Instruments Incorporated