參數資料
型號： TPS524
英文描述： PHOTOVOLTAIC CELL FOR THERMOPILE DETECTION
中文描述： 光伏電池的熱電堆檢測
文件頁數： 21/29頁
文件大?。?/td> 500K
代理商： TPS524
TPS5210
PROGRAMMABLE SYNCHRONOUS BUCK REGULATOR CONTROLLER
SLVS171A – SEPTEMBER 1998 – REVISED MAY 1999
21
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
frequency calculation
A detailed derivation of frequency calculation is shown in the application report, “Designing Fast Response
Synchronous Buck Regulators Using the TPS5210”, TI Literature number SLVA044. When less accurate results
are acceptable, the simplified equation shown below can be used:
f
s
V
O
V
I
V
O
ESR
V
I
L
Hysteresis Window
Control Section
Below are the equations needed to select the various components within the control section. Details and the
derivations of the equations used in this section are available in the application report “Designing Fast Response
Synchronous Buck Regulators Using the TPS5210”, TI Literature number SLVA044.
output voltage selection
Of course the most important function of the power supply is to regulate the output voltage to a specific value.
Values between 1.3 V and 3.5 V can be easily set by shorting the correct VID inputs to ground. Values above
the maximum reference voltage (3.5 V) can be set by setting the reference voltage to any convenient voltage
within its range and selecting values for R2 and R3 to give the correct output. Select R3:
R3 << than V
REF
/I
BIAS(VSENSE)
; a recommended value is 10 k
Then, calculate R2 using:
V
O
V
REF
1
R2
R3
R2
R3
V
O
V
REF
V
REF
or
R2 and R3 can also be used to make small adjusts to the output voltage within the reference-voltage range
and/or to adjust for load-current active droop compensation. If there is no need to adjust the output voltage, R3
can be eliminated. R2, R3 (if used), and C7 are used as a noise filter; calculate using:
C7
150 ns
R2
R3
slowstart timing
Slowstart reduces the startup stresses on the power-stage components and reduces the input current surge.
Slowstart timing is a function of the reference-voltage current (determined by R6) and is independent of the
reference voltage. The first step in setting slowstart timing will be to determine R6:
R6 should be between 7 k
and 300 k
, a recommended value is 20 k
.
Set the slowstart timing using the formula:
C5
t
SS
R
VREFB
5
t
SS
(5
R6)
Where C5
= Slowstart capacitance in
μ
F
t
SS
= Slowstart timing in
μ
s
R
VREFB
= Resistance from VREFB to GND in ohms (
≈
R6)
Powered by ICminer.com Electronic-Library Service CopyRight 2003
相關PDF資料
PDF描述
TPS5300DAP Analog IC
TPS535G1 PHOTOVOLTAIC CELL FOR THERMOPILE DETECTION
TPS535G10 PHOTOVOLTAIC CELL FOR THERMOPILE DETECTION
TPS535G14 PHOTOVOLTAIC CELL FOR THERMOPILE DETECTION
TPS535G2 PHOTOVOLTAIC CELL FOR THERMOPILE DETECTION
相關代理商/技術參數
參數描述
TPS5300 制造商:TI 制造商全稱:Texas Instruments 功能描述:MOBILE CPU POWER SUPPLY CONTROLLER
TPS5300DAP 功能描述:DC/DC 開關控制器 Mobile CPU DC/DC Cntrlr RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
TPS5300DAPG4 功能描述:DC/DC 開關控制器 Mobile CPU DC/DC Cntrlr RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
TPS5300DAPR 功能描述:DC/DC 開關控制器 Mobile CPU DC/DC Cntrlr RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
TPS5300DAPRG4 功能描述:DC/DC 開關控制器 Mobile CPU DC/DC Cntrlr RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*